American Dynamics RAS915LS Operator'S Manual Download Page 98

Page: 98 / 124

Supported Keyboards

The following AD keyboards are compatible with SpeedDome Ultra VII when used with a suitable
AD-UTC host:

Keyboard

Presets

Patterns

Quick Set Menu

ADCC0200 96

Yes

ADCC0300 96

Yes

This list of keyboards is complete as of the time of publication. Other keyboards may be supported.
Contact your Sales Representative for current information.

Performance Notes

Keep the following considerations in mind when using the SpeedDome Ultra VII camera dome in the
AD-UTC environment.

Address Setting

The SpeedDome Ultra VII camera dome must be set to address

891

to operate in the AD-UTC

environment. When the dome initializes or resets, the address and protocol information (UTC_T)
appear on-screen.

Accessing the Quick Set Menu

The Quick Set Menu provides easy access to specific SpeedDome Ultra VII functions from the

keyboard. To access the Quick Set menu, select the dome, and press

(

Quick Set

button).

Figure E-1: Quick Set Menu

0 TOGGLE QUICK SET MENU
1 DOME CONFIG MENU
2 AUTO

IRIS/AUTO

FOCUS

3 FLIP
4 PEEL

PATTERN

15 SMOOTH

SCAN

16 STEPPED

SCAN

17 RANDOM

SCAN

20 DOME

INFORMATION

Enter a number and press

to use a quick set function. The following table describes the options.

E–4

SpeedDome Ultra VII Operator's Manual

Summary of Contents for RAS915LS





























































































































Search results

Summary of Contents for RAS915LS

Reviews:

Brands by name

Popular brands

American Dynamics RAS915LS, Operator'S Manual

Search results

Summary of Contents for RAS915LS

Reviews:

Brands by name

Popular brands