American Dynamics RAS915LS Operator'S Manual Download Page 84

Page: 84 / 124

Supported SpeedDome Ultra VII Features

The following SpeedDome Ultra VII features are supported with Coaxitron and P protocols:

•

11X digital zoom (up to 242X total zoom)

•

85 Total Presets (1-32, 35-87)

•

3 Patterns

•

16 Areas

•

4 Alarm Inputs and Outputs

•

8 Privacy Zones

•

Programmable Names (camera, preset, pattern, areas, and alarms)

•

Open Shutter settings

•

Proportional Flip

•

Direction Indicator display

•

Multi-language Dome Configuration Utility (available in English, French, German, Italian,
Portuguese, and Spanish) with Password Protection

Unsupported SpeedDome Ultra VII Features

The following SpeedDome Ultra VII features are not supported with the Pelco Coaxitron and “P”
protocols:

•

Save and exit from configuration menus using

Iris Close

and

Focus

keys

•

Apple Peel pattern (default SpeedDome pattern)

•

V-Phase adjustment

C–2

SpeedDome Ultra VII Operator's Manual

Summary of Contents for RAS915LS





























































































































Search results

Summary of Contents for RAS915LS

Reviews:

Related manuals for RAS915LS

Brands by name

Popular brands

American Dynamics RAS915LS, Operator'S Manual

Search results

Summary of Contents for RAS915LS

Reviews:

Related manuals for RAS915LS

Brands by name

Popular brands