manualshive.com logo in svg

American Dynamics RAS915LS, Operator'S Manual

Share
Download
American Dynamics RAS915LS Operator'S Manual Download Page 40

Setting the North Position 

Direction Indicators

 permit you to understand the approximate pointing position of the dome to an 

established reference point. This reference point is called “North” and may correspond to magnetic 
north (if it is known) or some other landmark or fixture. When the dome is initially installed, “North” 
defaults to a pre-defined position (0° pan/tilt). You may program the “North” position to be any point 
along the dome's pan axis (also called 

azimuth

).  

For more information about Direction Indicators, see

 Chapter 5

.  

Programming the North Position 

1. Select 

Alarms/Areas/Home/Presets/PZ

 from the 

Dome Configuration Menu

. 

2. Select 

Set North Position

. 

The 

Set North Position

 screen appears: 

SET NORTH POSITION

PAN to new north position

ZOOM to mark north position

FOCUS quits w/o changing

 

3.  Point the dome to the new North position. When satisfied with the view, save the setting, or 

cancel the change. 

4. The 

Alarms/Areas/Home/Presets/PZ 

screen appears. Select 

Exit

. The 

Dome Configuration 

Menu

 appears. Continue with 

What To Do Next

 on page 4–20.  

4–8 

SpeedDome Ultra VII Operator's Manual

 

Summary of Contents for RAS915LS





























































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands