background image

 

SPEEDDOME ULTRA VII CAMERA DOME CONFIGURATION UTILITY 

8200-0184-09, REV. A 

OPERATOR’S MANUAL SUPPLEMENT 

9 of 13

 

MegaPower LT  

Supported Protocol 

SensorNet 

Maximum Presets 

96 

Maximum Patterns (1) 

Quick Set Menu 

Yes (2) 

Address Range 

1-32 

Notes: 

 (1)  Patterns are limited by time and the number of 

available dome commands. Total time for each 
pattern cannot exceed 6 minutes 50 seconds. Total 
dome commands used in all patterns cannot exceed 
99. 

(2)   Requires a compatible keyboard. 

MegaPower 48  

Supported Protocol 

SensorNet  

RS-422  

Maximum Presets 

96(1) 

Maximum Patterns (2) 

Quick Set Menu 

Yes (3) 

Address Range 

1-48 

Notes: 

(1)   Preset information is stored at the host, not the 

dome. 

(2)   Patterns are limited by time and the number of 

available dome commands. Total time for each 
pattern cannot exceed 6 minutes 50 seconds. Total 
dome commands used in all patterns cannot exceed 
99. 

(3)   Requires firmware 1.07 or newer and a compatible 

keyboard.  

MegaPower 1024 

Supported Protocol 

RS-422 (1) 

Maximum Presets 

16 (2) or 60 (3) 

Maximum Patterns (4) 

Quick Set Menu 

Not supported 

Address Range 

1-1024 (5) 

Notes: 

(1)  Requires the AD2083-02 series code converter. 

(2)  Preset information is stored at the converter, not the 

dome. 

(3)  Requires AD2083-02 with firmware version 0701-

11YB-156A or newer. Preset information is stored in 
the dome, not the converter. 

(4)  Patterns are limited by time and the number of 

available dome commands. Total time for each 
pattern cannot exceed 6 minutes 50 seconds. Total 
dome commands used in all patterns cannot exceed 
99. 

(5)  Requires additional equipment to achieve these 

numbers. A dome address within each group of 64 
or 99 cameras is reserved as a global broadcast 
address.

 

 

Panasonic UTC Protocol 
Preset Programming  

The Dome Configuration Menu must be used to 
program Presets. Up to 64 Presets may be 
programmed using the Panasonic UTC protocol. 

These instruction apply to the following equipment: 

• 

Panasonic WJ-SX550 Multiplexer 

• 

Panasonic WV-CU550A Controller 

1.  Select the monitor and camera number 

assigned to the Speed Dome Ultra VII camera 
dome. 

2.  Use the arrow keys on the controller to scroll to 

the 

Camera Setup Menu 

(D4). 

3. Press 

F1

 (On) key to display the 

Dome 

Configuration Menu

4.  Use the joystick to move the highlight to 

Alarms/Areas/Home/Presets/PZ

. Press 

Set

 

to select. 

ALARMS/AREAS/HOME/PRESETS/PZ

SET ALARM ACTIONS

SET ALARM STATES

SET HOME POSITION

SET NORTH POSITION

AREA BOUNDARIES

PRIVACY ZONES

PRESETS

SCAN LIMITS

EXIT

 

Summary of Contents for RAS915














Reviews: