background image

8

American Dryer Corp.

113431 - 10

M50SL Specifications _______________________________________________________________

!

Shaded areas are stated in metric equivalents

4/30/07

Note

The manufacturer reserves the right to make changes in specifications at any time without notice or obligation.

MAXIMUM CAPACITY (DRY WEIGHT)

50 lb

22.68 kg

TUMBLER DIAMETER

37”

93.98 cm

TUMBLER DEPTH

25-3/4”

65.41 cm

TUMBLER VOLUME

16.02 cu ft

453.64 L

TUMBLER/DRIVE MOTOR

3/4 hp

0.56 kW

BLOWER/FAN MOTOR

1/2 hp

0.37 kW

DOOR OPENING (DIAMETER)

27-3/8”

69.53 cm

DOOR SILL HEIGHT

16”

40.64 cm

WATER CONNECTION

3/4”-11.5 NH 

(North America)

3/4” B.S.P.T.

 (Outside North America)

DRYERS PER 20’/40’ CONTAINER

10 / 22

DRYERS PER 48’/53’ TRUCK

28 /  30

VOLTAGE AVAILABLE

120-240V    1ø    2w    50/60 Hz

APPROXIMATE NET WEIGHT

545 lb

247.21 kg

APPROXIMATE SHIPPING WEIGHT

565 lb

256.28 kg

AIRFLOW

60 Hz

525  cfm

14.87 cmm

50 Hz

437 cfm

12.37 cmm

HEAT INPUT

90,000  Btu/hr

22,680 kcal/hr

EXHAUST CONNECTION (DIAMETER)

8”

20.32 cm

COMPRESSED AIR CONNECTION

N / A

COMPRESSED AIR VOLUME

N / A

INLET PIPE CONNECTION

1/2” M.N.P.T.

1/2” F.B.S.P.T.

 (CE and Australia Only)

VOLTAGE AVAILABLE

120-600V    1,3ø    2,3,4w    50/60 Hz

APPROXIMATE NET WEIGHT

545 lb

247.21 kg

APPROXIMATE SHIPPING WEIGHT

565 lb

256.28 kg

AIRFLOW

60 Hz

525  cfm

14.87 cmm

50 Hz

437 cfm

12.37 cmm

EXHAUST CONNECTION (DIAMETER)

8”

20.32 cm

COMPRESSED AIR CONNECTION

N / A

COMPRESSED AIR VOLUME

N / A

OVEN SIZE

kW

Btu/hr

kcal/hr

13.4

45,869

11,559

14.7

50,136

12,634

14.8

50,545

12,737

16.0

54,606

13,761

VOLTAGE AVAILABLE

120-240V    1ø    2w    50/60 Hz

APPROXIMATE NET WEIGHT

545 lb

247.21 kg

APPROXIMATE SHIPPING WEIGHT

565 lb

256.28 kg

AIRFLOW

60 Hz

525  cfm

14.87 cmm

50 Hz

437 cfm

12.37 cmm

STEAM CONSUMPTION

127.5 lb/hr

57.83 kg/hr

OPERATING STEAM PRESSURE

150 psi max

10.34 bar

EXHAUST CONNECTION (DIAMETER)

8”

20.32 cm

COMPRESSED AIR CONNECTION

N / A

COMPRESSED AIR VOLUME

N / A

BOILER HORSEPOWER (NORMAL LOAD)

3.75 Bhp

SUPPLY CONNECTION

3/4” F.N.P.T.

RETURN CONNECTION

3/4” M.N.P.T.

Gas

Electric

Steam

Summary of Contents for M31SL































Reviews: