manualshive.com logo in svg

AMD Elan SC520, User Manual, Page: 242 / 444

Share
Download
AMD Elan SC520 User Manual Download Page 242

ROM/Flash Controller

12-12

Élan™SC520 Microcontroller User’s Manual

width of the ROM device, e.g., if a 16-bit write is performed to an 8-bit ROM, two Am5

x

86 

CPU write cycles are generated to complete the operation. 

All write access to Flash devices must occur in units no smaller than the data width of the 
device. For example, 8-bit writes to a 16-bit Flash device are not allowed. Care should be 
taken to also avoid 24-bit writes to 16-bit Flash devices, because this generates two Flash 
cycles, one with a complete 16-bit write and another with an 8-bit write to a 16-bit Flash 
device.

Figure 12-11 Word Write Cycle to Flash Memory

12.5.4

Software Considerations

12.5.4.1

Address Decoding

The ROM controller does not perform address decoding. Address decoding for chip select 
generation is provided by the Programmable Address Region (PAR) registers. In addition 
to the regions defined in the PAR registers, a default region from FFFF0000–FFFFFFFFh 
is defined at system reset to handle early code fetches from the boot ROM. See Chapter 3, 
“System Initialization”, and Chapter 4, “System Address Mapping”, for further details on 
configuring the address regions for ROM chip selects and the shadowing of ROM. 

12.5.4.2

Programming Flash Memory

Flash is available in 8-bit and 16-bit versions and is organized into sectors. Sectors can be 
of fixed or variable size and range from 8–32 Kbytes. New, higher density Flash devices 
have sector sizes of up to 256 Kbytes. 

Several programmable operations can be performed on Flash devices, including sector 
erase, sector protect, and programming of individual bytes. 

■

The erased value of a byte is 0FFh. 

■

Bits can be programmed from a 1 to a 0. 

■

If any bit in a sector needs to be changed from a 0 to a 1, the entire sector must be 
erased and reprogrammed. 

Most Flash devices cannot be programmed while the Am5

x

86 CPU is fetching data from 

it, requiring the programming code to reside in another device during programming. This 

address

W

CPU clock

ads

GPA25–GPA0

GPD15–GPD0, or

rdy

FLASHWR

BOOTCS

MD15–MD0

bs16

Summary of Contents for Elan SC520





























































































































































































































































































































































































































































Reviews:

No comments