manualshive.com logo in svg

AMD AMD-761, Software/Bios Design Manual, Page: 14 / 264

Share
Download
AMD AMD-761 Software/Bios Design Manual Download Page 14

2

Overview

Chapter 1

AMD-761™ System Controller Software/BIOS Design Guide

24081D—February 2002 

Preliminary Information

1.1

General BIOS Initialization Requirements

The following sections provide general requirements for BIOS
w h e n   p r o g ra m m i n g   t h e   A M D -7 6 1   s y s t e m   c o n t r o l l e r
configuration registers. Note that the register descriptions also
include some specific programming notes.

1.1.1

AMD-761™ Configuration Spaces

The AMD-761 system controller contains both I/O and memory-
mapped configuration spaces as listed below.

„

I/O Mapped Space

•

PCI configuration space address and data (CF8h, CFCh)

•

Host bridge registers mapped in PCI configuration
space, device 0, function 0

•

DDR interface PDL and I/O controls mapped in PCI
configuration space to device 0, function 1

•

PCI to PCI bridge/AGP registers mapped in PCI
configuration space to device 1, function 0

„

GART Memory-Mapped Registers

•

Mapped in memory space as defined by the
programming of Base Address 1: GART Memory Mapped
Register Base

1.1.2

Special Configuration Sequencing Requirements

This section outlines a few cases in the AMD-761 system
controller  configuration registers that require special handling
for proper BIOS programming.

Configuration Cycles 
Enable

The AMD-761 system controller  supports configuration
address space as defined by the 

PCI Local Bus Specification

,

Revision 2.2, which defines a unique 256-byte space that is
accessed through two 32-bit index registers mapped in I/O
space.

As defined in the PCI specification, configuration cycles are
generated on the PCI bus only when bit 31 of the Configuration
Address register is set. 

Summary of Contents for AMD-761









































































































































































































































































Reviews:

No comments