Ambient Weather WS-3000-X8 User Manual Download Page 32

 

Version 1.2  

©Copyright 2020, Ambient LLC. All Rights Reserved. 

 

 

 

Page  32 

 

Increase the separation between the equipment and receiver.   

 

Connect the equipment into an outlet on a circuit different from that to which the receiver is 
connected.   

 

Consult the dealer or an experienced radio/TV technician for help.   

 

13

 

  Warranty Information 

Ambient,  LLC  provides  a  1-year  limited  warranty  on  this  product  against  manufacturing  defects  in 
materials and workmanship. 
 
This limited warranty begins on the original date of purchase, is valid only on products purchased and 
only to the original purchaser of this product. To receive warranty service, the purchaser must contact 
Ambient, LLC for problem determination and service procedures.   
 
Warranty service can only be performed by a Ambient, LLC. The original dated bill of sale must be 
presented upon request as proof of purchase to Ambient, LLC. 
 
Your  Ambient,  LLC  warranty  covers  all  defects  in  material  and  workmanship  with  the  following 
specified exceptions: (1) damage caused by accident, unreasonable use or neglect (lack of reasonable 
and necessary maintenance); (2) damage resulting from failure to follow instructions contained in your 
owner’s manual; (3) damage resulting from the performance of repairs or alterations by someone other 
than an authorized Ambient, LLC authorized service center; (4) units used for other than home use (5) 
applications and uses that this product was not intended (6) the products inability to receive a signal 
due  to  any  source  of  interference  or  metal  obstructions  and  (7)  extreme  acts  of  nature,  such  as 
lightning strikes or floods.   
 
This  warranty  covers  only  actual  defects  within  the  product  itself,  and  does  not  cover  the  cost  of 
installation  or  removal  from  a  fixed  installation,  normal  set-up  or  adjustments,  claims  based  on 
misrepresentation  by  the  seller  or  performance  variations  resulting  from  installation-related 
circumstances. 
 

14

 

California Prop 65 

WARNING:

 Use of the Ambient Weather Products can expose you to chemicals, including lead and 

lead compounds, which are known to the State of California to cause cancer and bisphenol A (BPA), 
and phthalates DINP and/or DEHP, which are known to the State of California to cause birth defects 
or other reproductive harm. 
 

Can I Trust that Ambient Weather Products are Safe Despite this Warning?

 

 
In 1986, California voters approved the Safe Drinking Water and Toxic Enforcement Act known as 
Proposition 65 or Prop 65. The purpose of Proposition 65 is to ensure that people are informed about 
exposure to chemicals known by the State of California to cause cancer, birth defects and/or other 
reproductive harm. A company with ten or more employees that operates within the State of California 
(or sells products in California) must comply with the requirements of Proposition 65. To comply, 
businesses are: (1) prohibited from knowingly discharging listed chemicals into sources of drinking 
water; and (2) required to provide a "clear and reasonable" warning before knowingly and 
intentionally exposing anyone to a listed chemical. Proposition 65 mandates that the Governor of 
California maintain and publish a list of chemicals that are known to cause cancer, birth defects and/or 
other reproductive harm. The 

Prop 65 list

, which must be updated annually, includes over 1,000 

chemicals, including many that are commonly used in the electronics industry. 

Summary of Contents for WS-3000-X8


































Reviews: