background image

 

Version 1.5  

 

©Copyright 2017, Ambient LLC. All Rights Reserved. 

 

 

 

Page 12 

9

 

Liability Disclaimer 

Please help in the preservation of the environment and return used batteries to an authorized depot.   
The  electrical  and  electronic  wastes  contain  hazardous  substances.  Disposal  of  electronic  waste  in 
wild country and/or in unauthorized grounds strongly damages the environment. 
 
Reading the “User manual” is highly recommended. The manufacturer and supplier cannot accept any 
responsibility for any incorrect readings and any consequences that occur should an inaccurate reading 
take place. 
 
This product is designed for use in the home only as indication of weather conditions. This product is 
not to be used for medical purposes or for public information. 
 
The specifications of this product may change without prior notice. 
 
This product is not a toy. Keep out of the reach of children. 
 
No part of this manual may be reproduced without written authorization of the manufacturer. 
 
Ambient,  LLC  WILL  NOT  ASSUME  LIABILITY  FOR  INCIDENTAL,  CONSEQUENTIAL, 
PUNITIVE,  OR  OTHER  SIMILAR  DAMAGES  ASSOCIATED  WITH  THE  OPERATION  OR 
MALFUNCTION OF THIS PRODUCT. 

10

 

FCC Statement 

Statement according to FCC part 15.19: 

 

This device complies with part 15 of the FCC rules. Operation is subject to the following two 
conditions:   

1.

 

This device may not cause harmful interference.   

2.

 

This device must accept any interference received, including interference that may cause 
undesired operation.   
 

Statement according to FCC part 15.21: 

 

Modifications not expressly approved by this company could void the user's authority to operate the 
equipment. 

Statement according to FCC part 15.105: 

 

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital 
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable 
protection against harmful interference in a residential installation. This equipment generates, uses and 
can radiate radio frequency energy and, if not installed and used in accordance with the instructions, 
may cause harmful interference to radio communications.   
However, there is no guarantee that interference will not occur in a particular installation. If this 
equipment does cause harmful interference to radio or television reception, which can be determined 
by turning the equipment off and on, the user is encouraged to try to correct the interference by one or 
more of the following measures:   

 

Reorient or relocate the receiving antenna.   

 

Increase the separation between the equipment and receiver.   

 

Connect the equipment into an outlet on a circuit different from that to which the receiver is 
connected.   

 

Consult the dealer or an experienced radio/TV technician for help.   

 

Summary of Contents for F007PF














Reviews: