Amazone ZA-M Profis Hydro Operating Manual Download Page 32

Page: 32 / 104

Product description

ZA-M BAG0040.8 09.15

Fig. 7/…

(1) Frame

(2) Hopper

(3) Omnia-set spreading discs

(4) Setting lever for rate slide

(5) Collection bucket for the spread rate check

(6) Weighing frame

(7) Control terminal

(8) Hydraulic control block

(9) Oil filter

(10) Cover for machine computer and cable harness

(11) Dirt trap

(12) Agitator shaft

4.2

Safety and protection equipment

(13) Chain guard of agitator shaft drive to prevent contact with the

running chain drive

(14) Protective planks at rear to prevent contact with the rotating

spreading vanes

(15) Protective planks at side to prevent contact with the rotating

spreading vanes

(16) Guard and function screen in the hopper to prevent contact with

the rotating agitator spiral

(17) Upper and lower deflector plates to prevent fertiliser being

thrown forward

(18) Guard screen in the lower section of the hopper to prevent con-

tact with the rotating agitator spiral

(19) Warning pictograms

4.3

Supply lines between the tractor and the machine

Fig. 8/...

(1) Hydraulic hose lines

(2) Cable with connection for lighting

(3) Computer cable with machine connector

Fig. 8

Summary of Contents for ZA-M Profis Hydro









































































































Search results

Summary of Contents for ZA-M Profis Hydro

Reviews:

Brands by name

Popular brands

Amazone ZA-M Profis Hydro, Operating Manual

Search results

Summary of Contents for ZA-M Profis Hydro

Reviews:

Brands by name

Popular brands