Amazone Pantera 4503 Operating Manual Download Page 70

Page: 70 / 120

Settings

ISOBUS field sprayer BAG0171.9 11.20

5.2.6

Configuring boom behavior

•

Working height (height of the spraying noz-
zle) in cm

•

Lift boom on the headlands

Off (do not lift)

Low (+10 in / 25 cm)

Medium (+ 20 in / 100 cm)

High (+ 30 in / 150 cm)

Only ContourControl:

•

Activate / deactivate the distance sensors,
see page 71.

•

Boom guidance sensitivity

Low (low forward speed, heterogene-
ous crop)

Medium

High (high forward speed, homogene-
ous crop)

•

Mode (Profi 2)

Angle up

Tilt adjustment

•

Maximum angle up

Default value 100% (maximum possible

angle)

•

Maximum angle down

Default value 100% (maximum possible

angle)

BOOM BEHAVIOR

Working height

Lift on headlands

Activate distance sensors

Boom guidance sensitivity

Mode

Maximum angle up

Maximum angle down

Summary of Contents for Pantera 4503

























































































































Search results

Summary of Contents for Pantera 4503

Reviews:

Brands by name

Popular brands

Amazone Pantera 4503, Operating Manual

Search results

Summary of Contents for Pantera 4503

Reviews:

Brands by name

Popular brands