manualshive.com logo in svg

Amazone Pantera 4503, Operating Manual

Share
Download
Amazone Pantera 4503 Operating Manual Download Page 47

 

 

 

 

Field menu 

 

ISOBUS field sprayer  BAG0171.9  11.20

 

47 

 

Road transport – road mode 

 

DANGER 

Risk of accident due to faulty steering of the implement when the 
axle is steered! 

For safety reasons during road transport, move the steering axle to 
transport position!

 

 

  1.  Move the sprayer boom into transport 

position. 

  2. 

 Activate the locking 

mechanism before road travel. 

  3.  When driving off, the axle moves to the 

center position and is automatically locked. 

 

 

For road travel,  

lock steering 

 

 

 

4.7.2 

Hydropneumatic spring suspension 

 

Manual mode, automatic mode 

   

 

 

Lowering / lifting the implement in manual mode 

 

 

When both terminals are switched on, the spring suspension starts in 
automatic mode. 

Always drive the implement in automatic mode. 

When automatic mode is switched on, the implement computer con-
trols the height of the field sprayer independent of the tank volume. 

In manual mode, the machine can be lowered or lifted. 

 

Display in the Work menu: 

Hydropneumatic spring suspension 
in automatic mode (operating state). 

 

 

 

 

Summary of Contents for Pantera 4503

























































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands