Amazone Pantera 4503 Operating Manual Download Page 44

Page: 44 / 120

Field menu

ISOBUS field sprayer BAG0171.9 11.20

4.7

Axle function group

4.7.1

AutoTrail steering axle

Automatic / manual mode

Steer counter to the slope

Move to center position.

Lock the axle in transport position

Unlock the axle

DANGER

Danger of accident!

Automatic mode, manual mode and error state (error message pre-
sent) are prohibited during road travel.

→

Only drive on the road with the axle aligned straight and locked.

Automatic mode is prohibited when maneuvering.

→

Maneuver the implement in manual mode.

DANGER

Danger of the implement tipping over when the steering axle is
locked (turned to the end stop); particularly on very uneven or
sloping terrain!

Adapt your driving style accordingly and reduce speed when perform-
ing a turning maneuver on headlands, so that you are in complete
control of the tractor and implement.

Summary of Contents for Pantera 4503

























































































































Search results

Summary of Contents for Pantera 4503

Reviews:

Brands by name

Popular brands

Amazone Pantera 4503, Operating Manual

Search results

Summary of Contents for Pantera 4503

Reviews:

Brands by name

Popular brands