manualshive.com logo in svg

Amazone Pantera 4503, Operating Manual

Share
Download
Amazone Pantera 4503 Operating Manual Download Page 18

 

 

 

Field menu 

 

 

18 

 

ISOBUS field sprayer  BAG0171.9  11.20

 

 

4.3 

Functions in the Work menu 

 

4.3.1 

Switch spraying on / off 

 

Switch spraying on / switch spraying off 

 

•

 

Switch spraying on: Spray fluid is applied 
via the spraying nozzles. 

•

 

Switch spraying off: No spray liquid is ap-
plied. 

Display in the Work menu: 

 

 

 

Spraying switched on  

 

Spraying switched off  

 

4.3.2 

Switching on Start functions 

 

Switching on the start functions collectively 

 

Depending on the selected configuration, the 
following automatic process functions can be 
switched on simultaneously: 

 (1)  Section Control 

 (2)  Unlock the boom, boom ride 

 (3)  AutoTrail 

 (4)  Hydropneumatic spring suspension 

 (5)  AmaSelect 

 (6)  FlowControl  

 (7)  Hydraulic pump drive 

 

It is not possible to switch off the automated pro-
cesses collectively. 

Not all of the automatic functions are shown in 
the Work menu. 

 

 

 

 

Summary of Contents for Pantera 4503

























































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands