manualshive.com logo in svg

Amazone Centaya 3000 Special, Original Operating Manual

Get your hands on the Original Operating Manual for the Amazone Centaya 3000 Special at manualshive.com. Download the manual for free and unlock the full potential of your equipment. Ensure optimal performance and efficiency with the help of this essential guide. Don't miss out on this valuable resource!

Share
Download
background image

6.4.15 Operating the one-sided switching

The control lever on the left in the direction of travel

1

 actuates the left sliding shutter, opened here. The

control lever on the right in the direction of travel 

2

actuates the right sliding shutter, closed here.

2

1

CMS-I-00003596

1.

To actuate the desired sliding shutter manually,

swivel up the corresponding control lever.

or

To operate the electrically actuated sliding
shutter,

see "ISOBUS software" operating manual

or

see "control computer" operating manual.

2.

To halve the seed rate when using half the
working width,

see "ISOBUS software" operating manual

or

see "control computer" operating manual.

CMS-T-00004888-C.1

6 | Preparing the implement

Preparing the implement for operation 

MG7508-EN-GB | B.1 | 31.08.2022 | © AMAZONE

78

Summary of Contents for Centaya 3000 Special

































































































































































Reviews:

No comments

Related manuals for Centaya 3000 Special

Brands by name

Popular brands

Load more brands