Amazone Centaya 3000 Special Original Operating Manual Download Page 43

Page: 43 / 160

4.15.1.2 Additional license plate

Licence plate lighting

Licence plate holder

CMS-I-00003163

4.15.2 Work lights

The work floodlights

make the working area

more visible in the dark. The work floodlights are
switched on and off via the control terminal or control
computer.

CMS-I-00006845

The coulter array lighting

enables better visibility

of the seeding coulters in the dark. The coulter array
lighting is switched on and off together with the
work floodlights via the control terminal or control
computer.

CMS-I-00006848

CMS-T-00003999-B.1

CMS-T-00009795-A.1

4 | Product description

Lighting

MG7508-EN-GB | B.1 | 31.08.2022 | © AMAZONE

Summary of Contents for Centaya 3000 Special

































































































































































Search results

Summary of Contents for Centaya 3000 Special

Reviews:

Related manuals for Centaya 3000 Special

Brands by name

Popular brands

Amazone Centaya 3000 Special, Original Operating Manual

Search results

Summary of Contents for Centaya 3000 Special

Reviews:

Related manuals for Centaya 3000 Special

Brands by name

Popular brands