manualshive.com logo in svg

Amazone Catros 2503 Special, Operating Manual

Share
Download
Amazone Catros 2503 Special Operating Manual Download Page 54

 

 

 

Adjustments 

 

 

Reducing the working depth 

→

 More spacer elements 

behind

 the stop wash-

er 

  1.  Raise the coupled implement (unload the 

front spacer elements). 

  2.  Secure the tractor against unintentional 

rolling. 

  3.  Swivel the desired number of spacer ele-

ments in front of the stop washer away from 
the setting rod. 

  4.  Lower the implement onto the ground. 

  5.  Swivel spacer elements that are not in ac-

tion behind the stop washer. 

 

 

 

8.1.2 

Hydraulic working depth adjustment

 

Actuate tractor control unit 

green

.. The working 

depth is set hydraulically using the scale 

. 

The scale provides orientation for the set working 
depth 

 

 

 

8.2 

Working depth of the border elements 

The raised border elements at the front right and 
rear left must be adjusted 

Use the bearing pin and hub as handle. 

  1.  Secure the tractor against unintentional 

starting and unintentional rolling away. 

  2.  Undo three screw unions. 

  3.  Adjust the border elements in the elongated 

slots so that no ridge formation is caused 
during operation. 

  4.  Retighten the screw unions. 

 

 

 

54  

Catros  BAG0160.4  02.19 

 

Summary of Contents for Catros 2503 Special







































































Reviews:

No comments

Brands by name

Popular brands

Load more brands