5
How to reverse the
doors
1. Perform all steps listed in
How to
Remove the Doors and Hinges
.
2. Transfer cabinet plugs and cabinet
screws to opposite
side of cabinet.
• Remove cabinet
plugs with flat
blade of screw-
driver tip wrapped
in masking tape.
• Remove center
mullion screws
with
5
Ú
16
" hex head
driver.
•
For swing doors only:
Remove
bottom mullion screws with
3
Ú
8
" hex
head driver.
IMPORTANT:
When working directly on
doors, place doors on a nonabrasive
surface protected by towels or rugs to
avoid damage to door finish.
3. Transfer door stops from bottom edge
of fresh food door and freezer door
(some models) to opposite side of
door edge.
• Use a Phillips
screwdriver for
removal and
installation.
4. See
How to Install and Remove
Handles
to remove and reinstall
handles.
5. Proceed to
How to Replace the
Doors and Hinges
to mount doors.
DOORS WITH CONTOUR
DESIGN
1. Perform all steps listed in
How to
Remove the Doors and Hinges.
2. Transfer cabinet
plugs and screws to
opposite side of
cabinet.
• Remove plugs with flat blade of
screwdriver wrapped in masking
tape.
• Remove center mullion screws with
5
Ú
16
" hex head driver.
To avoid possible injury and damage
to property:
➢
Place doors on a nonabrasive sur-
face protected by towels or rugs
while working directly on doors.
➢
DO NOT
remove sub cap when
removing door trim.
CAUTION
3. Remove door stop
from fresh food
door with Phillips
screwdriver.
4. Remove bottom door trim by removing
4 Phillips screws. Lift handle corner of
trim and slide toward hinge edge of
door.
5. Remove top door trim by removing 4
screws. Lift handle corner of trim and
slide toward hinge edge of door.
• For white, bisque, and black models,
use a T-15 Torx
®
* head driver.
• For stainless steel models, use a
Phillips screwdriver.
• Retain all screws for later use.
6. Reverse handle by removing two T-15
Torx head screws from top and bottom
edge of handle and reattaching handle
on opposite side of door.
7. Install
top door trim
on
bottom
side
of door, and
bottom trim
on
top
side
of door.
• Locate hinge hole corner of trim.
Install hinge hole corner of trim on
hinge side first, then install handle
edge of trim.
8. Procede to
How to Replace the
Doors and Hinges
.
How to install and
remove handles
INSTALLING FRESH FOOD
FRONT-MOUNTED
HANDLES
If installing handles for the first time, the
fresh food handles can be located within
the fresh food section. The handle trim
will be located in the literature pack.
1. Remove
1
Ú
4
" hex head
screws from door face
with hex head driver.
• If reversing door,
remove door plugs
from opposite side of
door and insert in screw holes.
2. Align handle holes with screw
holes on door face and secure
with 2 door face
screws from step 1.
3. Locate handle trim in liter-
ature pack and install over
top and bottom of handle,
as illustrated.
• Secure top handle trim
with remaining screw
removed in step 1.
• Snap bottom trim over bottom por-
tion of handle.
REMOVING FRESH FOOD
FRONT-MOUNTED
HANDLES
Removing handles may be necessary
when transporting unit through tight
spaces, or when reversing the door.
1. Remove top handle trim by
removing top handle
screw.
• Retain trim and screw for
later replacement.
2. Pry bottom handle trim
from handle with screw-
driver flat blade wrapped
in masking tape.
• Retain trim for later
replacement.
*Torx
®
is a registered trademark of Textron Inc.