manualshive.com logo in svg

ALW MoonRing OnePointFive MR1.5, Installation Instructions Manual, Page: 5 / 12

Share
Download
ALW MoonRing OnePointFive MR1.5 Installation Instructions Manual Download Page 5

MR-RQ Installation Guide

5 of 12 

102-000031- IG071719-B.0

MR-RQ Installation Guide

Install remote driver J-Box(es) in an accessible/

serviceable location. Run low voltage wire from Remote 

Driver J-Box to Canopy J-Box in accordance with local/

state/federal regulations.

3

Install Remote Driver J-Box

Canopy Fittings may also be mounted using toggle bolts.

4

B

Install Canopy Fitting - Toggle Bolts

Canopy Fittings may also be mounted on 1/4”-20 

Threaded Rods.

4

C

Install Canopy Fitting - 1/4”-20 Threaded Rods

Installation: Prepare Ceiling

Canopy Fittings may be installed directly into framing with 

appropriate hardware.

4

A

Install Canopy Fitting - Framing

See final/record drawings for mounting locations. Install 

framing, strut or 1/4-20 ceiling rods to match mounting 

locations.

1

See Final/Record Drawings for Mounting Locations

SAMPLE DRAWING

Install Canopy J-Box 

(sold separately)

 at power feed 

location per final/record drawing.

2

Install Canopy J-Box

SAMPLE DRAWING

Summary of Contents for MoonRing OnePointFive MR1.5













Reviews:

No comments