manualshive.com logo in svg

Alvarion BreezeMAX PRO-S CPE, Product Manual

Share
Download
Alvarion BreezeMAX PRO-S CPE Product Manual Download Page 115

BST/AU ID Parameters Menu

BreezeMAX CPEs Product Manual 

93

The default Preferred BST/AU ID Mask is 0.0.0.0.0.0.

4.6.6

Selected BST/AU Parameters

Select this option to view the following details on the selected BST/AU:

„

Selected BST/AU ID

„

Selected Rx Frequency

„

RSSI of the received signal, in dBm

„

SNR of the received signal, in dB

„

Selected Rx Antenna

4.6.7

Set Mobility Mode

The Set Mobility Mode enables defining the expected mobility of the SU: nomadic 
or mobile.

4.6.8

Show Mobility Mode

Select this option to view the current Mobility Mode.

4.6.9

Best BST/AU Table

Select this option to view the following details for each of the BST(s)/AU(s) found 
during the scanning process:

„

BST/AU ID

„

Rx Frequency

„

SNR (dB)

„

Antenna

Summary of Contents for BreezeMAX PRO-S CPE



































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands