Alvarado SU2000, Installation Instructions Manual

Page: 21 / 34

Supervisor 2000 Installation Instructions
PUD1601R6-1 For Assistance: support@alvaradomfg.com +1 (909) 591-8431 Page 21
I/O Control Board (13-0328 Rev. F) Terminal Descriptions
J2 Output Contacts J1 Input Contacts
Pin # Pin
Name Function
Description Contact
Type Function & Behavior
Description
Pin # Pin
Name Function
Description Contact
Type Function & Behavior
Description
1 GNDX Ground N/A Common output signal
ground.
1 GND Ground N/A Common input ground signal.
2 ENTACX Authorized
Passage
Entry
MDC An output occurs when an
authorized entry passage is
completed.
2 ENTACC Good Card
Entry
MDC Opens the turnstile for one
authorized passage until
passage occurs or timeout.
3 ENTUCX Unauthorized
Passage
Entry
MDC An output occurs when an
unauthorized entry passage
is completed.
3 ENTREJ Bad Card
Entry
MDC Illuminates the entry side
RED User Status Icon for 2
seconds.
4 ENTALRX Unauthorized
Presence
Entry
MDC Not used on the SU2000. 4 ENTPAS Free
Passage
Entry
SDC Sets the turnstile to Free
Passage mode in the entry
direction.
5 ENTCLSX N/A N/A Reserved 5 ENTCLS Close
Direction
Entry
SDC Sets the turnstile to No
Passage mode in the entry
direction.
6 EXTACX N/A N/A Reserved 6 ENTOVR Single
Override
Entry
MDC Opens the turnstile for one
authorized passage in the
entry direction independent
of the access control system.
(Typically used for button at
security desk.)
7 GNDX Ground N/A Common output signal
ground.
7 ENTSERVICE Visitor Mode SDC Places the turnstile in Free
Passage in both the entry and
exit directions. (Typically used
with toggle switch at security
desk.)
8 EXTACX Authorized
Passage Exit
MDC An output occurs when an
authorized exit passage is
completed.
8 GND Ground N/A Common input ground signal.
9 EXTUCX Unauthorized
Passage Exit
MDC An output occurs when an
unauthorized exit passage is
completed.
9 EXTACC Good Card
Exit
MDC Opens the turnstile for one
authorized passage until
passage occurs or timeout.
10 EXTALRX Unauthorized
Presence
Exit
MDC Not used on the SU2000. 10 EXTREJ Bad Card
Exit
MDC Illuminates the exit direction
RED User Status Icon for 2
seconds.
11 EXTCLSX N/A N/A Reserved 11 EXTPAS Free
Passage
Exit
SDC Sets the turnstile to Free
Passage mode in the exit
direction.
12 EXTOVRX N/A N/A Reserved 12 EXTCLS Close
Direction
Exit
SDC Sets the turnstile to No
Passage mode in the exit
direction.
13 BLKSEN Blocked
Sensor
MDC An output occurs when
a sensor is blocked for a
defined length of time (default
15 seconds).
13 EXTOVR Single
Override
Exit
MDC Opens the turnstile for one
authorized passage in the
exit direction independent of
the access control system.
(Typically used for button at
security desk.)
14 SOUT-1 Free
Passage Exit
MDC An output occurs when there
is a passage in the exit
direction.
14 EXTSERVICE Horizontal
Arm
Breakaway
SDC Not used on the SU2000.
15 GNDX Ground N/A Common output signal
ground.
15 GND Ground N/A Common input ground signal.
16 DHO Loitering MDC An output occurs when a
user loiters in the lane after
the allotted time to close
after passage (default 12
seconds).
16 N/O Normally
Open
SDC Not used on the SU2000.
17 BREAKAWAY Barrier Arm
Broken Away
MDC Not used on the SU2000. 17 BARDISABLE Disables
Barrier Arms
SDC Not used on the SU2000.
18 SOUT-2 Crawl
Detection
MDC An output occurs when the
crawl sensors detect an
unauthorized passage.
18 EMROVR Emergency
Override
SDC
(N/O or
N/C)
Turnstile opens in the exit
direction. Turnstile is inactive
until SDC is removed, or
contact is reestablished if N/C
jumper is enabled. (Typically
used for fire alarm or life
safety systems.)
19 SOUT-3 N/A N/A Reserved 19 SINPUT N/A N/A Reserved
20 GNDX Ground N/A
Common output signal ground.
20 GND Ground N/A Common output signal ground.