Altuscn KM0032 User Manual Download Page 148

Page: 148 / 155

KM0032 / KM0532 / KM0932 User Manual

136

Factory Default Settings

The factory default settings are as follows (in alphabetical order):

Setting

Default

Accessible Ports

Super Administrators – Full for all ports

All other users – None for all ports.

Beeper

On (Activated)

Date & Time

Synchronize with my computer

Daylight Savings Time

Enabled

Default Gateway

192.168.0.254

DHCP Enabled

No (Disabled)

Hotkey Command Mode

On (Enabled)

HTTP Port

HTTPS Port

443

Interface Language

English

IP Address

192.168.0.10

Lockout Period

3 minutes

Logout Timeout

0 (Disabled)

Maximum Login Failures

Occupy Timeout

60 seconds

Port Access

None

(Super Administrators and Administrators have full

access)

Port ID Display Duration

User Defined (3 seconds)

Port ID Display Mode

The Port Number plus the Port Name

Port ID Display Position

Upper Left Corner

Port Language

U.S. English

Port Operating System

Windows (PC compatible)

Scan Duration

5 seconds

Scan Mode

Acce Powered

Screen Blanker

0 (Disabled)

SMTP Server Mail
Notification

No (Disabled)

Subnet Mask

255.255.255.0

Toolbar Hotkey

[Scroll Lock] [Scroll Lock]

View Mode

Acce Powered

Summary of Contents for KM0032




























































































































































Search results

Summary of Contents for KM0032

Reviews:

Altuscn KM0032, User Manual, Page: 148 / 155

Search results

Summary of Contents for KM0032

Reviews: