manualshive.com logo in svg

Altuscn KM0032, User Manual, Page: 106 / 155

Share
Download
Altuscn KM0032 User Manual Download Page 106

KM0032 / KM0532 / KM0932 User Manual

94

PON

If a Power over the NET™ (PON) module is connected to your installation 
clicking the PON menu item starts a Java Applet viewer that brings up its 
interface – allowing you to remotely power manage servers connected to the 
Matrix KVM Switch. (See

Association

, page 48.)

Note:

1. PON is only available with the Browser UI.

2. PON support is implemented through the browser via a Java Applet 

Viewer. Therefore, the latest version of Sun's Java Runtime 
Environment (JRE) must be installed on the client computer (the one 
you use to log into the Matrix KVM Switch with).

3. The PON viewer can only be used in the current browser session. If 

you log out, the applet will stop. You must download and run the 
applet again the next time you log in.

Once you download and run the Java Applet, the PON’s login screen comes up. 
Refer to the User Manual that came with your PON package for information on 
PON operation.

Note:

Visit our website for the latest information regarding our PON products.

Summary of Contents for KM0032




























































































































































Reviews:

No comments