manualshive.com logo in svg

Alto L-20, Operator'S Manual, Page: 1 / 29

Share
Download
Alto L-20 Operator'S Manual Download Page 1

READ THIS BOOK

This book has important information for the use and safe operation of this machine.  Failure to read this
book prior to operating or attempting any service or maintenance procedure to your ALTO machine could
result in injury to you or to other personnel; damage to the machine or to other property could occur as
well.  You must have training in the operation of this machine before using it.  If operator(s) cannot read
English, have this manual explained fully before attempting to operate this machine.

Si  Ud. o sus operadores no pueden leer el Inglés, se hagan explicar este manual completamente antes
de tratar el manejo o servicio de esta máquina.

All directions given in this book are as seen from the operator’s position at the rear of the machine.

For new books write to:  ALTO U.S. Inc.,  2100 Highway 265, Springdale,  Arkansas  72764.

Operator's

Manual

ENCORE

S20/L20

Form No. 74836B

8/05

CLARKE TECHNOLOGY                                            Printed in the U.S.A.

U.S. Patent No. 5,383,251; No. 6,105,192; No. 6,557,207; & Patent Pending

Summary of Contents for L-20






























Reviews:

No comments