background image

Page 11

Work Light II

Installation & Users Manual

Specifications

Notes:

* - Weight was taken with the 510 and Color Frame attached to the Fixture

Materials:

Materials:

Corrosion-resistant materials and hardware

Housing:

Housing:

Lightweight aluminum construction

Control:

Control:

Phase Cut or Triac Dimmer, or Constant power 

with on board local fader control.

Light Engine:

Light Engine:

90W LED Array - Available in 3000K or 5000K

Rated Lifespan:

Rated Lifespan:

Array rating >50,000 hours to L70

Input Voltage:

Input Voltage:

100-230 VAC 50/60 Hz

Wattage:

Wattage:

90 Watts

LED Engine Cooling:

LED Engine Cooling: Convection, passive

Convection, passive

Color Options:

Color Options:

Black or White. Custom colors - consult factory

Black or White. Custom colors - consult factory

Environment:

Environment:

0 - 40°C (32 - 104°F) with humidity of 5-95% 

0 - 40°C (32 - 104°F) with humidity of 5-95% 

non-condensing)

non-condensing)

Weight:

Weight:

11 lbs. (4.98 kg)*

11 lbs. (4.98 kg)*

Compliance:

Compliance:

cETLus listed for indoor use

cETLus listed for indoor use

Warranty:

Warranty:

Five (5) years and One (1) day

Five (5) years and One (1) day

Support:

Support:

Supported Forever - free phone and online tech 

Supported Forever - free phone and online tech 

support for the life of your product.

support for the life of your product.

Summary of Contents for WORK LIGHT II












Reviews: