TNP130 Podcast Tilt 'N Plug
®
Jr.
User’s Guide
400-0823-001
1
Welcome!
We greatly appreciate your purchase of your TNP130 Podcast
Tilt 'N Plug Jr. Interconnect Box. We are sure you will find it
reliable and simple to use. Superior performance for the right
price, backed by solid technical and customer support is what
Altinex offers.
We are committed to providing Signal Management Solutions
®
to
our customers for the most demanding audiovisual installations at
competitive pricing and we welcome you to join the ranks of our
many satisfied customers throughout the world.
1. Precautions and Safety Warnings
Please read this manual carefully before using your TNP130.
Keep this manual handy for future reference. These safety
instructions are to ensure the long life of your Tilt 'N Plug Jr. and
to prevent fire and shock hazards. Please read them carefully and
heed all warnings.
1.1 General
•
Qualified Altinex personnel or their authorized
representatives must perform all service.
1.2 Installation Precautions
•
For best results, place the Tilt 'N Plug Jr. in a dry area away
from dust. To prevent fire or shock, do not expose to water
or moisture. Do not place in direct sunlight, near heaters or
heat-radiating appliances, or near any liquid. Exposure to
direct sunlight, smoke, or steam can harm components.
•
Handle carefully; dropping or jarring can damage the bezel.
•
Never place fingers inside the opening on either side of the
unit; injury can occur due to sharp edges inside.
•
Do not place heavy objects on top of the TNP Jr. Do not
use excessive force to push down on the top of the unit.
•
Install all cables according to the instructions herein. Do not
force or pull any cable that is attached to the TNP Jr.
1.3 Cleaning
•
Surfaces should be cleaned with a dry cloth. Never use
strong detergents or solvents such as alcohol or thinner. Do
not use a wet cloth or water to clean the unit.
1.4 FCC Notice
•
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1) This
device may not cause harmful interference, and (2) this
device must accept any interference received, including
interference that may cause undesired operation.
•
This equipment has been tested and found to comply with
the limits for a Class A digital device, pursuant to Part 15 of
the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when
the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in
accordance with the instructions found herein, may cause
harmful interference to radio communications. Operation of
this equipment in a residential area is likely to cause
harmful interference in which case the user will be required
to correct the interference at his expense.
•
Any changes or modifications to the unit not expressly
approved by Altinex. could void the user’s authority to
operate the equipment.
2. Installation Procedures
Step 1. Cut an opening into the table’s surface. Refer to the Altinex website at
www.altinex.com
for table cutout requirements.
Note:
The table can be 2.25” (57mm) or less. Always confirm dimensions before cutting to ensure specifications have not changed.
Step 2. Insert the TNP130 into the table cutout.
Step 3. Place the support brackets under the table and place them between the
support mount grooves on the side of the unit. Attach brackets to the groove
at the desired height and secure them to the bottom of the table using the
knurled table securing screws provided with the additional wing nuts for
added tightening. See Diagram 3 for details.
Step 4. To lower the unit, push on the top cover until it locks into place.
Step 5. Secure the cables using the provided cable clamps and screws. Pass the
cables from the bottom of the housing and attach it to the table using the
cable clamp and screw supplied with the TNP Jr. Leave enough slack in the
service loop to allow for easy opening and closing, but not too much as to
cause excess drooping of the service loop.
Step 6. Connect the appropriate cables with the correct input connectors on the bottom of the unit.
For cough button see attached no terminated wires diagram.
Step 7. Once you connected the proper cables on the bottom of the unit you may raise the unit by
pushing down on the front of the top cover. The latching mechanism releases and the unit
raises into position. To lower the unit, push on the top of the TNP Jr. until it locks into place.
3. Limited Warranty/Return Policies
Please see the Altinex website at
www.altinex.com
for details on warranty and return policies.
