Altera Nios II Embedded Evaluation Kit Cyclone III Edition User Manual Download Page 22

Page: 22 / 80

Altera Corporation

Development Board Version 1.0.

2–2

July 2010

Nios II Embedded Evaluation Kit, Cyclone III Edition

Development Board Setup

Requirements

If not already installed, you should:

■

Install the Quartus II Web Edition software on the host computer. For
more information, refer to

“Installing the Quartus II Web Edition

Software” on page 1–9

■

Install the Nios II Embedded Evaluation Kit, Cyclone III Edition. For
more information, refer to

“Installing the Nios II Embedded

Evaluation Kit, Cyclone III Edition” on page 1–7

■

Install the USB-Blaster

™

driver software on the host computer. The

Cyclone III FPGA starter development board includes integrated
USB-Blaster circuitry for FPGA programming.

The USB Blaster driver software is provided with the Quartus II
software installation

Communication between the host

computer and the development board requires that the
USB-Blaster driver software be set up.

Power Up the
Development
Board

To power up the development board, perform the following steps:

Ensure that the red on/off switch (SW1)

on the back-side of the

development board is in the

OFF

position (up).

Connect the USB-Blaster cable from the host computer to the
USB-Blaster port on the development board.

Connect the 12-V DC adapter to the development board and to a
power source.

Only use the supplied 12-V power supply. Power regulation
circuitry on the board could be damaged by supplies greater
than 12 V.

Press the

Power Switch

(SW1).

A Welcome screen appears as shown in

Figure 2–1

Summary of Contents for Nios II Embedded Evaluation Kit Cyclone III Edition

















































































Search results

Summary of Contents for Nios II Embedded Evaluation Kit Cyclone III Edition

Reviews:

Related manuals for Nios II Embedded Evaluation Kit Cyclone III Edition

Brands by name

Popular brands

Altera Nios II Embedded Evaluation Kit Cyclone III Edition, User Manual

Search results

Summary of Contents for Nios II Embedded Evaluation Kit Cyclone III Edition

Reviews:

Related manuals for Nios II Embedded Evaluation Kit Cyclone III Edition

Brands by name

Popular brands