manualshive.com logo in svg

Altera Cyclone V, Device Handbook

Share
Download
Altera Cyclone V Device Handbook Download Page 260

Table 8-6: Error Type in EMR

The following table lists the possible error types reported in the error type field in the EMR.

Description

Error Type

Bit 0

Bit 1

Bit 2

Bit 3

No CRC error.

0

0

0

0

Location of a single-bit error is identified.

1

0

0

0

Location of a double-adjacent error is identified.

0

1

0

0

Error types other than single-bit and double-adjacent errors.

1

1

1

1

Table 8-7: JTAG Fault Injection Register Map

Description

Bit Range

Field Name

Contains the location of the bit error that
corresponds to the error injection type to this
field.

31:0

Error Byte
Value

Contains the location of the injected error in
the first data frame.

41:32

Byte Location

Specifies the following error types.

45:42

Error Type

Bit 42

Bit 43

Bit 44

Bit 45

No error

0

0

0

0

Single-bit error

1

0

0

0

Double adjacent error

0

1

0

0

Error Detection Process

When enabled, the user mode error detection process activates automatically when the FPGA enters user
mode. The process continues to run until the device is reset even when an error is detected in the current
frame.

Figure 8-4: Error Detection Process Flow in User Mode

Yes

No

Receive

Data Frame

Calculate and

Compare

CRC Values

Error

Detected?

Pull CRC_ERROR

Signal Low for

32 Clock Cycles

Update Error

Message Register

(Overwrite)

Search for

Error Location

Drive

CRC_ERROR

Signal High

Timing

The

CRC_ERROR

pin is always driven low during CRC calculation for a minimum of 32 clock cycles. When

an error occurs, the pin is driven high once the EMR is updated or 32 clock cycles have lapsed, whichever

Altera Corporation

SEU Mitigation for Cyclone V Devices

Send Feedback

8-7

Error Detection Process

CV-52008
2013.11.12

Summary of Contents for Cyclone V






















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands