Altera Cyclone V Device Handbook Download Page 114

Page: 114 / 1077

Figure 5-4: Phase Relationship for External PLL Interface Signals

D10

inclk0

RX serial data

D10

TX serial data

VCO clk

(internal PLL clk)

outclk0

(-180° phase shift)

outclk1

(288° phase shift)

outclk2

(-18° phase shift)

tx_outclk

Connection between Altera_PLL and ALTLVDS

Figure 5-5: LVDS Interface with the Altera_PLL Megafunction

This figure shows the connections between the Altera_PLL and ALTLVDS megafunction.

Transmitter

Core Logic

tx_coreclk

LVDS Transmitter

(ALTLVDS)

LVDS Receiver

(ALTLVDS)

rx_inclock

Receiver

Core Logic

rx_coreclk

rx_enable

pll_areset

rx_out

tx_inclock

tx_enable

tx_in

Altera_PLL

inclk0

pll_areset

outclk0

outclk2

outclk1

locked

FPGA Fabric

When generating the Altera_PLL megafunction, the Left/Right PLL option is configured to set up the PLL
in LVDS mode. Instantiation of

pll_areset

is optional.

Guideline: Use the Same V

CCPD

for All I/O Banks in a Group

In the Cyclone V devices, all I/O banks have individual V

CCPD

except the following I/O bank groups, which

share V

CCPD

in each group:

• Banks 1A (if available) and 2A
• Banks 3B and 4A
• Banks 7A and 8A

Altera Corporation

I/O Features in Cyclone V Devices

Send Feedback

5-17

Connection between Altera_PLL and ALTLVDS

CV-52005
2014.01.10

Summary of Contents for Cyclone V






















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Cyclone V

Reviews:

Brands by name

Popular brands

Altera Cyclone V, Device Handbook

Search results

Summary of Contents for Cyclone V

Reviews:

Brands by name

Popular brands