Altera Arria V GZ User Manual Download

Page: 55 / 300

Chapter 3: Getting Started with the Avalon-MM Arria V GZ Hard IP for PCI Express

3–17

Compiling the Design

November 2012

Altera Corporation

Arria V GZ Hard IP for PCI Express

User Guide

2. Click

Next

in the

New Project Wizard:

Introduction

(The introduction does not

appear if you previously turned it off.)

3. On the

Directory, Name, Top-Level Entity

page, enter the following information:

a. For What is the working directory for this project, browse to

<project_dir>

/ep_g1x4/synthesis/

b. For

What is the name of this project

, select

ep_g1x4

from the

synthesis

directory.

4. Click

Next

5. On the

Add Files

page, add

<project_dir>

/ep_g1x4/synthesis/ep_ge1_x4.qip

your Quartus II project. This file lists all necessary files for Quartus II compilation,
including the

altera_pci_express.sdc

that you just modified.

6. Click

Next

to display the

Family & Device Settings

page.

7. On the

Device

page, choose the following target device family and options:

a. In the

Family

list, select

Arria V GZ

b. In the

Devices

list, select

All

c. In the

Available devices

list, select

5AGZME5K2F40C3

8. Click

Next

to close this page and display the

EDA Tool Settings

page.

9. From the

Simulation

list, select

ModelSim

. From the

Format

list, select the HDL

language you intend to use for simulation.

10. Click

Next

to display the

Summary

page.

11. Check the

Summary

page to ensure that you have entered all the information

correctly.

Compiling the Design

Follow these steps to compile your design:

1. On the Quartus II Processing menu, click

Start Compilation

2. After compilation, expand the

TimeQuest Timing Analyzer

folder in the

Compilation Report. Note whether the timing constraints are achieved in the
Compilation Report.

If your design does not initially meet the timing constraints, you can find the
optimal Fitter settings for your design by using the Design Space Explorer. To use
the Design Space Explorer, click

Launch Design Space Explorer

on the tools

menu.

Programming a Device

After you compile your design, you can program your targeted Altera device and
verify your design in hardware.

For more information about programming Altera FPGAs, refer to

Quartus II

Programmer

Summary of Contents for Arria V GZ













































































































































































































































































































Search results

Summary of Contents for Arria V GZ

Reviews:

Related manuals for Arria V GZ

Brands by name

Popular brands

Altera Arria V GZ, User Manual

Search results

Summary of Contents for Arria V GZ

Reviews:

Related manuals for Arria V GZ

Brands by name

Popular brands