Altera Arria V GZ User Manual Download | Manualshive

Page: 54 / 300

background image

3–16

Chapter 3: Getting Started with the Avalon-MM Arria V GZ Hard IP for PCI Express

Understanding Channel Placement Guidelines

Arria V GZ Hard IP for PCI Express

November 2012

Altera Corporation

User Guide

Understanding Channel Placement Guidelines

Arria V GZ transceivers are organized in banks of six channels. The transceiver bank
boundaries are important for clocking resources, bonding channels, and fitting. Refer
to the channel placement figures following

“Serial Interface Signals” on page 6–54

illustrations of channel placement for ×1, ×4, and ×8 variants using both CMU and
ATX PLLs.

f

For more information about transceiver clocking and channel placement refer to
“Transceiver Clocking and Channel Placement Guidelines” in

Configurations in Arria V GZ Devices

Adding Synopsis Design Constraints

Before you can compile your design using the Quartus II software, you must add a
few Synopsys Design Constraints (SDC) to your project. Complete the following steps
to add these constraints:

1. Browse to

<project_dir>

/ep_g1x4/synthesis/submodules

.

2. Add the constraints shown in

Example 3–2

to

altera_pci_express.sdc

.

1

Because

altera_pci_express.sdc

is overwritten each time you regenerate your design,

you should save a copy of this file in an additional directory that the Quartus II
software does not overwrite.

Creating a Quartus II Project

You can create a new Quartus II project with the New Project Wizard, which helps
you specify the working directory for the project, assign the project name, and
designate the name of the top-level design entity. To create a new project follow these
steps:

1. On the Quartus II File menu, click

New,

then

New Quartus II Project

, then

OK

.

Example 3–1. Transcript from ModelSim Simulation of Gen1 x4 Endpoint (continued)

# INFO:        54368 ns Setup BAR = 2
# INFO:           54368 ns   Length = 000512, Start Offset = 000000
# INFO:           60609 ns Interrupt Monitor: Interrupt INTA Asserted
# INFO:           60609 ns Clear Interrupt INTA
# INFO:           62225 ns Interrupt Monitor: Interrupt INTA Deasserted
# INFO:           69361 ns MSI recieved!
# INFO:           69361 ns   DMA Read and Write compared okay!
# SUCCESS: Simulation stopped due to successful completion!
# Break at ./..//ep_g1x4_tb/simulation/submodules//altpcietb_bfm_log.v line 78

Example 3–2. Synopsys Design Constraints

create_clock -period “100 MHz” -name {refclk_pci_express} {*refclk_*}
create_clock -period "125 MHz" -name {reconfig_xcvr_clk}
{*reconfig_xcvr_clk*}
derive_pll_clocks
derive_clock_uncertainty

«
...
52
53
54
55
56
...
»

Summary of Contents for Arria V GZ













































































































































































































































































































Reviews:

No comments

Related manuals for Arria V GZ

Brand: Sunrich Tech Pages: 4

X-FI FATAL1TY - SB X-FI PLATINIUM FATAL1TY QUICKSTART BACK EN FR DE IT ES NL

Brand: Creative Pages: 1

Brand: Gigabyte Pages: 36

Brand: SMC Networks Pages: 44

Brand: Hegel Pages: 4

Air Xpert DWL-AG520

Brand: D-Link Pages: 12

Brand: D-Link Pages: 33

Air Xpert DWL-AG520

Brand: D-Link Pages: 53

Brand: Hama Pages: 28

Brand: Lava Pages: 1

Brand: Lava Pages: 4

LAVA SSerial-PCIe

Brand: Lava Pages: 1

Brand: Acer NeWeb Pages: 20

Brand: Syris Pages: 7

Brand: Konig Pages: 48

Brand: Ingenico Pages: 22

Brand: Ingenico Pages: 23

Brand: Unigraf Pages: 23

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands