Altera Arria V GZ User Manual Download Page 167

Page: 167 / 300

Chapter 7: Register Descriptions

7–9

Altera-Defined Vendor Specific Extended Capability (VSEC)

November 2012

Altera Corporation

Arria V GZ Hard IP for PCI Express

User Guide

Table 7–18

defines the

CvP Programming Control

the programming software to control CvP programming.

Refer to

Configuration via Protocol (CvP) Implementation in Altera FPGAs User Guide

for

more information about using CvP.

Table 7–19

defines the fields of the

Uncorrectable Internal Error Status

This register reports the status of the internally checked errors that are uncorrectable.
When specific errors are enabled by the

Uncorrectable Internal Error Mask

PCI

Express Base Specification 3.0

. This register is for debug only. It should only be used to

observe behavior, not to drive logic custom logic.

Table 7–18. CvP Programming Control Register

Bits

Register Description

Reset Value

Access

[31:2]

Reserved.

0x0000

[1]

START_XFER

. Sets the CvP output to the FPGA control block indicating the start

of a transfer.

1’b0

[0]

CVP_CONFIG

. When asserted, instructs that the FPGA control block begin a

transfer via CvP.

1’b0

Table 7–19. Uncorrectable Internal Error Status Register

Bits

Register Description

Access

[31:12]

Reserved.

[11]

When set, indicates an RX buffer overflow condition in a posted request or Completion

RW1CS

[10]

Reserved.

[9]

When set, indicates a parity error was detected on the Configuration Space to TX bus interface

RW1CS

[8]

When set, indicates a parity error was detected on the TX to Configuration Space bus interface

RW1CS

[7]

When set, indicates a parity error was detected in a TX TLP and the TLP is not sent.

RW1CS

[6]

When set, indicates that the Application Layer has detected an uncorrectable internal error.

RW1CS

[5]

When set, indicates a configuration error has been detected in CvP mode which is reported as
uncorrectable. This bit is set whenever a

CVP_CONFIG_ERROR

rises while in

CVP_MODE

RW1CS

[4]

When set, indicates a parity error was detected by the TX Data Link Layer.

RW1CS

[3]

When set, indicates a parity error has been detected on the RX to Configuration Space bus
interface.

RW1CS

[2]

When set, indicates a parity error was detected at input to the RX Buffer.

RW1CS

[1]

When set, indicates a retry buffer uncorrectable ECC error.

RW1CS

[0]

When set, indicates a RX buffer uncorrectable ECC error.

RW1CS

Summary of Contents for Arria V GZ













































































































































































































































































































Search results

Summary of Contents for Arria V GZ

Reviews:

Related manuals for Arria V GZ

Brands by name

Popular brands

Altera Arria V GZ, User Manual

Search results

Summary of Contents for Arria V GZ

Reviews:

Related manuals for Arria V GZ

Brands by name

Popular brands