Altec ATP-4310 User Manual Download

Page: 79 / 89

- 72 -

7.3 Setting Ethernet by Diagnostic Tool

The Diagnostic Utility is enclosed in the CD disk \Utilities directory. Users can use Diagnostic Tool to

setup the Ethernet by RS-232, USB and Ethernet interfaces. The following contents will instruct users

how to configure the Ethernet by these three interfaces.

7.3.1 Using USB interface to setup Ethernet interface

Connect the printer and computer with USB cable.

Turn on the printer power switch.

Start the Diagnostic Utility by double clicking on the

icon.

The Diagnostic Utility default interface setting is USB interface. If USB interface is connected with

printer, no other settings need to be changed in the interface field.

Click on the “Ethernet Setup” button from “Printer Function” group in Printer Configuration tab to

setup the IP address, subnet mask and gateway for the on board Ethernet.

Summary of Contents for ATP-4310


























































































Search results

Summary of Contents for ATP-4310

Reviews:

Related manuals for ATP-4310

Brands by name

Popular brands

Altec ATP-4310, User Manual

Search results

Summary of Contents for ATP-4310

Reviews:

Related manuals for ATP-4310

Brands by name

Popular brands