Altec ATP-4310 User Manual Download

Page: 78 / 89

- 71 -

7.2 Printer Function

1. Connect the printer and computer with a cable.

2. Select the PC interface connected with bar code printer.

USB cable

Other cable

The default interface setting is USB
interface. If USB interface is
connected with printer, no other
settings need to be changed in the
interface field.

3. Click the “Printer Function” button to setup.

4. The detail functions in the Printer Function Group are listed as below.

Function

Description

Calibrate Sensor

Calibrate the sensor specified in the Printer
Setup group media sensor field

Ethernet Setup

Setup the IP address, subnet mask, gateway for
the on board Ethernet

RTC Setup

Synchronize printer Real Time Clock with PC

Factory Default

Initialize the printer and restore the settings to
factory default.

Reset Printer

Reboot printer

Print Test Page

Print a test page

Configuration Page

Print printer configuration

Dump Text

To activate the printer dump mode.

Ignore AUTO.BAS

Ignore the downloaded AUTO.BAS program

Exit Line Mode

Exit line mode.

Password Setup

Set the password to protect the settings

For more information about Diagnostic Tool, please refer to the diagnostic utility quick start

guide in the CD disk \ Utilities directory.

Summary of Contents for ATP-4310


























































































Search results

Summary of Contents for ATP-4310

Reviews:

Related manuals for ATP-4310

Brands by name

Popular brands

Altec ATP-4310, User Manual

Search results

Summary of Contents for ATP-4310

Reviews:

Related manuals for ATP-4310

Brands by name

Popular brands