Altec ATP-4310 User Manual Download

Page: 68 / 89

- 61 -

6.3.2

Sensor

This option is used to calibrate the selected sensor. We recommend calibrate the sensor

before printing when changing the media.

Item

Description

Default

Status

This function is available to check the printer’s sensor status.

N/A

Gap Mode

This item is used to set the gap media sensor type and
calibrate the sensor.

N/A

Bline Mode

This item is used to set the black mark media sensor type and
calibrate the sensor.

N/A

Cont. Mode

This item is used to set the continuous media sensor type and
calibrate the sensor.

N/A

Automatic

Printer will feed 2 to 3 gap labels to calibrate the sensor
sensitivity automatically.

N/A

Manual

In case “Automatic” cannot apply to the media, please use
“Manual” function to set the paper length and gap/bline size
then scan the backing/mark to calibrate the sensor sensitivity.

N/A

Pre-Printed

This function can set the min. paper length and max gap/bline
length before auto-calibrate the sensor sensitivity.

N/A

Main

Menu

Setup

Sensor

Status

Calibration

Gap Mode

Automatic

Manual

Pre-Printed

Bline Mode

Automatic

Manual

Pre-Printed

Cont. Mode

Automatic

Manual

Summary of Contents for ATP-4310


























































































Search results

Summary of Contents for ATP-4310

Reviews:

Related manuals for ATP-4310

Brands by name

Popular brands

Altec ATP-4310, User Manual

Search results

Summary of Contents for ATP-4310

Reviews:

Related manuals for ATP-4310

Brands by name

Popular brands