32
-EN
The setting of Parametric EQ/Graphic EQ Adjustment, Time Correction
and X-Over can be adjusted in this mode.
Adjusting the Parametric Equalizer Curve
You can modify the Equalizer settings to create a response curve more
appealing to your personal taste. To adjust the Parametric Equalizer
Curve, set the EQ mode to PARAMETRIC EQ. For details, refer to
“Setting EQ mode” (page 34).
1
After selecting EQ ADJ (Parametric EQ) from the
Sound Field Adjustment mode, turn the
Double
Action encoder
to select the band adjustment, and
then press
/ENTER
.
BAND1
BAND2
BAND3
BAND4
BAND5
BAND1
2
Turn the
Double Action encoder
to select an item
to adjust, then press
/ENTER
.
Frequency Adjustment
3
-1 Turn the
Double Action encoder
to select
frequency bands.
Adjustable frequency bands:
20 Hz to 20 kHz (in 1/3 octave steps)
BAND1: 20 Hz~80 Hz (63 Hz)
BAND2: 50 Hz~200 Hz (150 Hz)
BAND3: 125 Hz~3.2 kHz (400 Hz)
BAND4: 315 Hz~8 kHz (1 kHz)
BAND5: 800 Hz~20 kHz (2.5 kHz)
Level Adjustment
3
-2 Turn the
Double Action encoder
to adjust the
level.
Adjustable level: –6 to +6 dB
Bandwidth (Q) Adjustment
3
-3 Turn the
Double Action encoder
to set the
bandwidth (Q).
Adjustable bandwidth: 1, 1.5, 3
4
To adjust another band, repeat steps 1 to 3 and
adjust all bands.
•
The frequencies of adjacent bands cannot be adjusted within 4 steps.
•
While adjusting the Parametric EQ, you should consider the
frequency response of the connected speakers.
•
You can select the next band by pressing and turning the
Double
Action encoder
.
•
The User Preset screen can be recalled in the normal mode by
pressing and holding PRESET for 2 seconds.
Adjusting the Graphic Equalizer Curve
You can modify the equalizer settings to create a response curve more
appealing to your personal taste. To adjust the graphic equalizer curve,
set the EQ mode to GRAPHIC EQ. For details, refer to “Setting EQ
mode” (page 34).
1
After selecting EQ ADJ (Graphic EQ) from the Sound
Field Adjustment mode, turn the
Double Action
encoder
to select the band adjustment, and then
press
/
ENTER
.
BAND1
BAND2
BAND3
BAND4
BAND5
BAND6
BAND7
BAND1
BAND-1 (63 Hz) / BAND-2 (150 Hz) / BAND-3 (400 Hz) /
BAND-4 (1 kHz) / BAND-5 (2.5 kHz) / BAND-6 (6.3 kHz) /
BAND-7 (17.5 kHz)
2
Press
/
ENTER
to activate the level adjusting
mode.
3
Turn the
Double Action encoder
to adjust the
level.
Adjustable output level: –6 to +6 dB
4
To adjust another band, repeat steps 1 to 3, and then
adjust all bands.
•
You can select the next band by pressing and turning the
Double
Action encoder
.
•
The User Preset screen can be recalled in the normal mode by
pressing and holding PRESET for 2 seconds.
Adjusting the Time Correction
Before performing the following procedures, refer to “About Time
Correction” (page 35).
1
After selecting TIME CORRECTION from the Sound
Field Adjustment mode, turn the
Double Action
encoder
to select the band adjustment, and then
press
/ENTER
.
2.2ch (3WAY) System
4.2ch (FRONT/REAR/SUBW.) System
2
Press
/ENTER
to activate the Time Correction
input mode.
3
Turn the
Double Action encoder
to adjust the
distance
(0.0 to 336.6cm).
L = (distance to farthest speaker) – (distance to other
speakers)
Refer to “Time Correction Value List” on page 35.
Sound Field Adjustment
FC
LV
Q
FC
(frequency) (level) (bandwidth) (frequency)
F-L (Initial setting)
F-R
R-L
R-R
(Mid-L)
(Mid-R) (High-L ) (High-R)
SW-L
SW-R
F-L
(Mid-L)
F-L (Initial setting)
F-R
R-L
R-R
(Front-L)
(Front-R) (Rear-L) (Rear-R)
SW-L
SW-R
F-L
(Front-L)
