20
-EN
Turning Subwoofer ON/OFF
When the subwoofer is on, you can adjust the subwoofer output level
(refer to page 19).
For iDA-X200, the following setting can be made only when the
IMPRINT audio processor (PXA-H100) is not connected.
1
Press and hold
IMPRINT
(iDA-X200 only) or
SOUND
(iDA-X300 only) for at least 2 seconds to
activate the AUDIO selection mode.
2
Turn the
Double Action encoder
(iDA-X200 only)
or
Rotary encoder
(iDA-X300 only) to select the
SUBW mode, and then press
/
ENTER
.
SUBW
SUBW SYSTEM
*
BASS
TREBLE
HPF
SUBW
* Displayed only when subwoofer is ON.
3
Turn the
Double Action encoder
(iDA-X200 only)
or
Rotary encoder
(iDA-X300 only) to select SUBW
ON/OFF, and then press
/
ENTER
.
ON
OFF
4
Press
to return to normal mode.
•
If no operation is performed for 15 seconds, the unit will return to
normal mode automatically.
•
If
is pressed during setting, the unit returns to the previous item.
Setting the Subwoofer System
When the subwoofer is on, you can select either SYS 1 or SYS 2 for the
desired subwoofer effect.
For iDA-X200, the following setting can be made only when the
IMPRINT audio processor (PXA-H100) is not connected.
1
Press and hold
IMPRINT
(iDA-X200 only) or
SOUND
(iDA-X300 only) for at least 2 seconds to
activate the AUDIO selection mode.
2
Turn the
Double Action encoder
(iDA-X200 only)
or
Rotary encoder
(iDA-X300 only) to select the
SUBW SYSTEM mode, and then press
/
ENTER
.
SUBW
SUBW SYSTEM
*
BASS
TREBLE
HPF
SUBW
* Displayed only when subwoofer is ON.
3
Turn the
Double Action encoder
(iDA-X200 only)
or
Rotary encoder
(iDA-X300 only) to select the
SUBW SYS 1 or SUBW SYS 2, and then press
/
ENTER
.
SYS 1
SYS 2
4
Press
to return to normal mode.
•
If no operation is performed for 15 seconds, the unit will return to
normal mode automatically.
•
If
is pressed during setting, the unit returns to the previous item.
•
This function is inoperable when Subwoofer is set to OFF.
Setting the Bass Control
You can change the Bass Frequency emphasis to create your own tonal
preference.
For iDA-X200, the following setting can be made only when the
IMPRINT audio processor (PXA-H100) is not connected.
1
Press and hold
IMPRINT
(iDA-X200 only) or
SOUND
(iDA-X300 only) for at least 2 seconds to
activate the AUDIO selection mode.
2
Turn the
Double Action encoder
(iDA-X200 only)
or
Rotary encoder
(iDA-X300 only) to select the
BASS Adjustment mode, and then press
/
ENTER
.
SUBW
SUB SYSTEM
*
BASS
TREBLE
HPF
SUBW
* Displayed only when subwoofer is ON.
3
-1
*1
Turn the
Double Action encoder
(iDA-X200 only)
or
Rotary encoder
(iDA-X300 only) to select the
desired bass level (–7~+7), and then press
/
ENTER
.
You can emphasize or weaken the bass level.
3
-2 Turn the
Double Action encoder
(iDA-X200 only)
or
Rotary encoder
(iDA-X300 only) to select the
desired bass bandwidth, and then press
/
ENTER
.
Changes the boosted bass bandwidth to wide or narrow. A
wider setting will boost a wide range of frequencies above
and below the center frequency. A narrower setting will
boost only frequencies near the center frequency.
3
-3 Turn the
Double Action encoder
(iDA-X200 only)
or
Rotary encoder
(iDA-X300 only) to select the
desired bass center frequency, and then press
/
ENTER
.
80(Hz)
100(Hz)
200(Hz)
60(Hz)
80(Hz)
Emphasizes the displayed bass frequency ranges.
4
Press
to return to normal mode.
•
If no operation is performed for 15 seconds, the unit will return to
normal mode automatically.
•
If
is pressed during setting, the unit returns to the previous item.
•
The function is inoperable when DEFEAT is set to ON.
*
1
The adjustment can also be made by pressing IMPRINT (iDA-X200
only) or SOUND (iDA-X300 only). Refer to “Adjusting Subwoofer/
Bass/Treble/Balance(Between Left and Right)/Fader (Between Front
and Rear)/Loudness/Defeat” (page 19).
Setting the Bass Level
Setting the Bass Bandwidth
Setting the Bass Center Frequency
