17
-EN
Adjusting the Frequency (CENTER FRQ)
Adjustable frequency bands: 20 Hz to 20 kHz
Setting the Bandwidth (WIDTH (Q))
Setting contents:
3.0 (Initial setting) / 4.0 / 5.0
Adjusting the Level (LEVEL)
Setting contents:
−7 to +7 (Initial setting: ±0)
Notes
• BAND2 and BAND8 are the same as the Bass and Treble controls.
Their Level adjustment can also be controlled by pressing
Y
SETUP
and selecting Bass Level or Treble Level. Refer to “Adjusting Subwoofer
Level/Bass Level/Treble Level/Balance (Between Left and Right)/Fader
(Between Front and Rear)/Defeat” on page 15.
• Settings exceeding the frequency of adjacent bands are not available.
• While adjusting the 9BAND P-EQ, you should consider the frequency
response of the connected speakers.
• The 9-Band, Parametric EQ is used to customize the EQ PRESETS
settings.
The output level of each source is individually adjustable. For example, if
the TUNER level sounds lower than CD, its output can be adjusted
without affecting the other sources.
Setting item:
SOURCE VOL
Further setting items:
TUNER / DISC / USB / IPOD / BT AUDIO
/ PANDORA / AUX
Setting contents:
−14 dB ~ +14 dB (Initial setting: ±0)
Before performing the following procedures, refer to “About the
Crossover” on page 21.
Setting item:
X-OVER
1
Turn the
Rotary encoder
to select the channel, and then
press
ENTER
.
2WAY System
FRONT (HPF)
REAR (HPF)
SUBW LPF
FRONT (HPF)
3WAY System
LOW (LPF)
MID LOW (HPF)
MID HIGH (LPF)
HIGH (HPF)
LOW
2
Turn the
Rotary encoder
to select the desired item, and
then press
ENTER
.
Selecting the Cut-Off Frequency (FREQUENCY)
2WAY System
Setting contents:
20 / 25 / 31.5 / 40 / 50 / 63 / 80 (Initial setting) / 100 / 125 /
160 / 200 (Hz)
3WAY System
Setting contents:
LOW/MID LOW:
20 / 25 / 31.5 / 40 / 50 / 63 / 80 / 100 / 125 / 160 / 200 / 250 / 315 /
400 / 500 (Initial setting) / 630 / 800 (Hz)
MID HIGH:
20 / 25 / 31.5 / 40 / 50 / 63 / 80 / 100 / 125 / 160 / 200 / 250 / 315 /
400 / 500 / 630 / 800 / 1 k / 1.2 k / 1.6 k / 2 k / 2.5 k / 3.2 k / 4 k /
5 k (Initial setting) / 6.3 k / 8 k / 10 k / 12.5 k / 16 k / 20 k (Hz)
HIGH:
1 k / 1.2 k / 1.6 k / 2 k /2.5 k / 3.2 k / 4 k / 5 k (Initial setting) / 6.3 k /
8 k / 10 k / 12.5 k / 16 k / 20 k (Hz)
Note
• The frequency of MID LOW should not be more than the frequency of
MID HIGH.
Adjusting the Slope (SLOPE)
2WAY System
Setting contents:
FLAT / 6 / 12 / 18 / 24 (dB/oct.)
3WAY System
Setting contents:
FLAT / 6 / 12 (dB/oct.)
Note
• The Initial setting of 2WAY is FLAT, 3WAY is 12.
Adjusting the Level (LEVEL)
2WAY System/3WAY System
Setting contents:
−12 to 0 (dB) (Initial setting: 0)
Note
• The level setting results of MID LOW and MID HIGH in 3WAY system
are linkage.
3
Repeat steps 1 to 2 to make adjustment to the other
channels.
When the subwoofer is on, you can adjust the subwoofer output level
(refer to “Adjusting Subwoofer Level/Bass Level/Treble Level/Balance
(Between Left and Right)/Fader (Between Front and Rear)/Defeat” on
page 15).
Setting item:
SUBWOOFER
Setting contents:
OFF / ON (Initial setting)
OFF:
No subwoofer signal is output from the Subwoofer RCA
Connectors (refer to “Connections” on page 50).
ON:
The subwoofer signal is output from the Subwoofer RCA
Connectors (refer to “Connections” on page 50).
Band1
20 Hz ~ 100 Hz (63 Hz)
Band2
63 Hz ~ 315 Hz (125 Hz)
Band3
125 Hz ~ 500 Hz (250 Hz)
Band4
250 Hz ~ 1 kHz (500 Hz)
Band5
500 Hz ~ 2 kHz (1 kHz)
Band6
1 kHz ~ 4 kHz (2 kHz)
Band7
2 kHz ~ 7.2 kHz (4 kHz)
Band8
5.8 kHz ~ 12 kHz (8 kHz)
Band9
9 kHz ~ 20 kHz (16 kHz)
Setting the Source Volume Level
Adjusting the Crossover Settings
(X-OVER)
Turning Subwoofer ON/OFF
00ALPINE.book Page 17 Thursday, October 23, 2014 4:15 PM
