alphatronics DLM-600 Installer/User Manual Download Page 13 | Manualshive

Page: 13 / 39

background image

DLM-600 installer & user manual Rev. 1.3

16-11-2011

13 / 39

PROGRAMMING

L

OCAL PROGRAMMING WITH A COMPUTER OR LAPTOP

The DLM-600 is programmed locally using a programming cable (art. 003 834) and a computer / laptop
with the Alpha Tool software (art.code 004 255) version 2.4 or higher.
First connect the DLM-600 to the PC / laptop using the programming cable. The programming cable has
a Sub-D connector 9-pin female that is connected to the serial port of the computer (RS232), the 10-pin
ribbon cable connector is connected to the DLM-600 dialer.

Start the AlphaTool software and make sure that AlphaTool is ready to connect to the DLM-600 dialer.
Now connect the power supply to the DLM-600 and AlphaTool will now automatically connect to the
DLM-600.
For the correct operation of the DLM-600 dialer is important that the programming cable is unplugged.
This is only connected during programming and disconnected immediately afterwards.

For a complete description of the AlphaTool softwarepackage, see ‘AlphaTool manual’

STATUS SCREEN

When there is a connection between the DLM-600 and AlphaTool then the following status screen will be
displayed.

figure 4. Status screen

«
...
11
12
13
14
15
...
»

Summary of Contents for DLM-600








































Reviews:

No comments

Related manuals for DLM-600

Brand: Saftronics Pages: 62

Brand: Microtek Pages: 17

Brand: T+A Pages: 74

Brand: Varan Pages: 27

Brand: Kramer Pages: 15

Brand: Delta Pages: 1

basic-line DCC 1-00

Brand: axing Pages: 4

Brand: Linear Pages: 3

Brand: Advantech Pages: 4

Brand: Denon Pages: 65

Brand: SIIG Pages: 34

Brand: Cairn Pages: 5

Brand: Mitsubishi Pages: 96

SM-Universal Encoder Plus

Brand: Control Techniques Pages: 112

Brand: Kiloview Pages: 50

Brand: red lion Pages: 4

Brand: Baudcom Pages: 12

Brand: IBASE Technology Pages: 62

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands