alphatronics AlphaCom XL Service Manual Download Page 72

Page: 72 / 74

Service manual AlphaCom XL transceiver Rev. 1.4 10-08-2011

Blz. 72/74

APPENDIX G: SIA-codes

For certain functions and programming options it is possible to program a SIA / SIA-HS code. The codes
used are usually determined together with the central station. In the table below you will find a list of the
most commonly used codes.

SIA code

Definition

Description

AC Restore

(230V restore)

AC Trouble

(230V failure)

Burglary Alarm

Burglary Restoral

Opening

(Disarming message)

Automatic Closing Failed

(Attempt to automatically arm has failed).

Also used if the system has been „disarmed to long‟‟ when a partition containing a
„safe detector‟ has been disarmed longer than the time programmed.

Late Close

(Restoral of partition that was disarmed to long)

Closing

(Arming)

Duress

(Disarming under threat)

Fire Alarm

Fire Restoral

Holdup Alarm

Holdup Restoral

Medical Alarm

Medical Restoral

Opening

(Disarming)

Test message

Reset

(Start-up message of the system)

Tamper Alarm

Tamper Restoral

Undefined Alarm

(Technical alarm)

Undefined Restoral

(Restore message of Technical alarm or tamper)

Xmitter Supervision Restoral

(Restore of supervision message of a wireless detector)

Xmitter Restoral

(Restore of low-battery message of a wireless detector)

Xmitter Supervision

(Supervision alarm of a wireless detector)

Xmitter Trouble

(Low-battery message of a wireless detector)

Battery Restoral

(Restore of low-battery control panel)

Battery Trouble

(Low-battery control panel)

Summary of Contents for AlphaCom XL











































































Search results

Summary of Contents for AlphaCom XL

Reviews:

Brands by name

Popular brands

alphatronics AlphaCom XL, Service Manual

Search results

Summary of Contents for AlphaCom XL

Reviews:

Brands by name

Popular brands