manualshive.com logo in svg

alphatronics AlphaCom XL, Service Manual

Share
Download
alphatronics AlphaCom XL Service Manual Download Page 71

Service manual AlphaCom XL transceiver              Rev. 1.4 10-08-2011             

 

Blz. 71/74 

APPENDIX F: COMPATIBLE CONTROL PANELS 

 
The AlphaCom XL transceiver has been tested with the following control panels: 
 

Producer: 

Control panel: 

Tested protocols: 

Acknowledge to control 
panel after delivery to 
destination 

Ademco 

4140 XMPT2 

Ademco Contact ID 

No 

Alphatronics 

AlphaVision NG 

SIA-HS 

SIA 
Scancom DTMF 1600 8/16 kanalen 

Yes 

Yes 
Yes 

Alphatronics 

AlphaVision EC 

SIA-HS 

SIA 
Scancom DTMF 1600 8/16 kanalen 

Yes 
Yes 
Yes 

Alphatronics 

AlphaHome 

SIA Level 2 

XSIA 
Contact ID 

Yes 
Yes 
Yes 

Alphatronics 

AlphaBox 

SIA Level 2 

XSIA 
Contact ID 

Yes 
Yes 
Yes 

Alphatronics 

DL-500 kiezer 

SIA-HS 

Scancom DTMF 1600 8/16 kanalen 

Yes 
Yes 

Alphatronics 

DL-400 kiezer 

Scancom DTMF 1600 8/16 
kanalen 

Scancom DTMF 1400 8/16 kanalen 

Yes 
Yes 

Alphatronics 

CP-508 

SIA-HS 

SIA Level 2 
Scancom DTMF 1600 8/16 kanalen 

Yes 
Yes 
Yes 

Alphatronics 

CP-500 

SIA-HS 

Yes 

Alphatronics 

CP-407 

Scancom DTMF 1600 8/16 
kanalen 

Scancom DTMF 1400 8/16 kanalen 

Yes 
Yes 

Alphatronics 

CP-700 

Scancom DTMF 1600 8/16 
kanalen 

Yes 

Alphatronics 

AGN 7310 

Scancom DTMF 1600 8/16 kanelen 

Yes 

Alphatronics 

SC8-2 

SIA-HS 

Yes 

Caddx 

NX-6 (SE) 

SIA regular 

Yes 

Caddx 

NX-8 (SE) 

SIA regular 

Yes 

Caddx 

NX-plus 

SIA regular 

Yes 

DSC 

Power 608 

SIA regular 

Yes 

Electronics Line 

Infinity 

SIA regular 

Yes 

MikroS 

CMK 470(S) 

SIA regular 

Yes 

MikroS 

CMK 680 

SIA regular 

Yes 

MikroS 

CMK 890 

SIA regular 

Yes 

Visonic 

PowerMax 

SIA Level 2 
Contact ID 

Yes 
Yes 

Visonic 

PowerMax Plus 

SIA Level 2 
Contact ID 
Scancom DTMF 1400 8/16 kanalen 

Yes 
Yes 
No 

Visonic 

PowerMax Pro  

SIA Level 2 
Contact ID 
Scancom DTMF 1400 8/16 kanalen 

Yes 
Yes 
No 

 

Note: 

a recent list of tested and supported control panels can be found at the Alphatronics website 

www.alphatronics.nl/helpdesk. 

Summary of Contents for AlphaCom XL











































































Reviews:

No comments

Brands by name

Popular brands

Load more brands