manualshive.com logo in svg

alphatronics AlphaCom XL, Service Manual

Share
Download
alphatronics AlphaCom XL Service Manual Download Page 36

Service manual AlphaCom XL transceiver              Rev. 1.4 10-08-2011             

 

Blz. 36/74 

If the AlphaCom XL is powered by the power supply from a control panel it is not necessary to program 
these options, the control panel has its own power failure and low battery status. 
 
The settings for 

GPRS connection

 determines what actions will be taken if the GPRS connection fails. This 

also applies when the GPRS connection is defined as a back-up connection and the option 

always active

 has 

been enabled. 
 
The settings for 

tamper switch

 apply for tamper switch S1 mounted on the AlphaCom XL board. This 

tamper switch can be used if the AlphaCom XL is mounted in a separate casing. It is advised to mount the 
AlphaCom XL in the same casing as the control panel. 
 
If the AlphaCom XL is mounted in a separate casing then tamper switch S1 can be fitted with a tamper 
spring. The appropriate SIA code should also be programmed in this screen. You must ensure that the casing 
used for the AlphaCom XL complies with regulations stated. It is also possible to use an external tamper 
switch and connect the wires from the tamper switch to an input on the AlphaCom XL. 
 
For the 

PSTN tamper loop

 a SIA code must also be programmed if the tamper loop option is used. When the 

PSTN connection between the analog dialer and the CMK input in the AlphaCom is disconnected a alarm 
message will be sent to the central station. 

 
 

Configuration inputs 1 to 6

 

 

 

 
When pressing the button „inputs & outputs‟ in the main menu, the following screen will appear. 
On the left-hand side of the screen new buttons will appear that allow you to change settings for the 12 
inputs, the PSTN interface, the RS-232 ports and the relay outputs. 
 
 

Summary of Contents for AlphaCom XL











































































Reviews:

No comments

Brands by name

Popular brands

Load more brands