manualshive.com logo in svg

alphatronics AlphaCom XL, Service Manual

Share
Download
alphatronics AlphaCom XL Service Manual Download Page 13

Service manual AlphaCom XL transceiver              Rev. 1.4 10-08-2011             

 

Blz. 13/74 

 

HARDWARE INSTALLATION

 

 
 

 

 

 

 

 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 
 
 

 
 

 

 

 
 
 

 
 
 
 
 
 
 
 

 

Figure 2:

 ALPHACOM XL connections 

 
The AlphaCom XL transceiver is powered through the +-16VDC terminal blocks 
 
Attention: when using the RS-485 bus you must take into consideration:  

 

the AlphaCom XL receives is power supply through the -+16VDC connections. This is always the 
case when the AlphaCom XL is delivered including power supply and batterypack in a synthetic 
casing. In this case for the RS-485 bus connections only the 0V, A and B wires must be connected. 
The +-terminal connection of the RS-485 bus must 

not

 be connected. 

 

the AlphaCom XL is powered by the RS-485 bus.  

 
 

DIP switch‟s 

Backup Telephone line 
connection 

Alarmdialer  
connection 

GPRS module

*)

 

Power supply     

connection 

LAN activity LED 

 (see LEDs) 

LAN connection 

4 Status LEDs 

(see LEDs) 

LAN Link LED 

Trouble output 

Watchdog LED 

12 Analog inputs 

GPRS LED 

Jumpers t.b.v. ingangen 
(spanning sturing ja/nee) 

0V for analog inputs 

+12V en 0V for relay 

Tamper switch 

Red LED: Priority switch 

of the Alarm dialer           

is active 

RS-485 bus connection (serial port 2) 

Jumpers for   
firmware update 

4x jumper to 

select OC 

output instead 

of relay output 

4x jumper to 

connect C-

contact of the  

relay with +12V 

RS-232 for flashing firmware(serial port 1) 

Jumper for PSTN     

tamper loop 

3 relay or OC    

outputs 

RS-485 master/slave: 
remove when using in 
combination with  
AlphaVision NG 

RS-232 (serial port 3) 

Summary of Contents for AlphaCom XL











































































Reviews:

No comments

Brands by name

Popular brands

Load more brands