background image

Table of Contents

1. INTRODUCTION

1.1

About the ELSD 2000 ............................................................................................................................. 4

1.2

What Is Included with the ELSD 2000 .................................................................................................... 4

1.3

Principle of Operation ............................................................................................................................. 5

2. INSTALLATION

2.1

What You Will Need ................................................................................................................................ 6

2.2

Unpacking ............................................................................................................................................... 6

2.3

Controls and Features ............................................................................................................................ 7

2.3.1 Front Panel .................................................................................................................................... 7

2.3.2 Left Side Panel .............................................................................................................................. 7

2.3.3 Right Side Panel ............................................................................................................................ 8

2.3.4 Rear Panel ..................................................................................................................................... 8

2.4

Making Electrical and Fluid Connections ................................................................................................ 9

3. INSTRUMENT CONTROL

3.1

ELSD 2000 Control Options ................................................................................................................. 12

3.2

Using the ELSD 2000 Control Panel .................................................................................................... 12

3.3

Navigating the Screens ......................................................................................................................... 12

3.4

Powering Up ......................................................................................................................................... 13

3.5

Operation Screen .................................................................................................................................. 13

3.6

Instrument Status .................................................................................................................................. 13

3.6.1 Standby ........................................................................................................................................ 13

3.6.2 Run .............................................................................................................................................. 13

3.7

Menu Screen ........................................................................................................................................ 14

3.8

Setting Up a Run .................................................................................................................................. 14

3.9

Method Screen ..................................................................................................................................... 15

3.10 Method Options .................................................................................................................................... 15

3.10.1 Select a Previously Saved Method ............................................................................................ 15

3.10.2 Edit an Existing Method ............................................................................................................. 16

3.10.3 Create a New Method ................................................................................................................ 17

3.11 Configuration Screen ............................................................................................................................ 17

1

Summary of Contents for ELSD 2000














































Reviews: