AllSportSystems STUDIOBAY Setup Manual Download Page 30

Page: 30 / 35

All

SportSystems, Inc.

2021

SIDE NETTING

You will receive two (2) sections of Side Netting. These will hang directly in front of your previously
installed side shades.

Side Netting is installed from the
floor up.

Step 1: Attach LEADING
EDGE to Velcro

Starting from the floor, attach
the Side Netting to the velcro
edge on the previously installed
Side Shades.

Step 2: Attach BOTTOM to
Black Bungee

Using zip ties, attach bottom of
Side Netting to the bottom black
bungee that runs under the
screen.

Step 3: Attach TOP to Cabling

Using Zip ties, attach top of Side
Netting to the top angled wall
cabling. DO NOT OVER
TIGHTEN. Evenly tension the
Side Netting with zip ties so that
it hangs flat.

The screen side edge of your
Side Netting will not attach to
anything. This edge hangs
freely to allow the fabric to
flex.

REPEAT STEPS FOR THE
OTHER SIDE NETTING

Page 30 of 35

Return to Table of Contents

Last Revised 6/7/22

Summary of Contents for STUDIOBAY




































Search results

Summary of Contents for STUDIOBAY

Reviews:

Related manuals for STUDIOBAY

Brands by name

Popular brands

AllSportSystems STUDIOBAY, Setup Manual

Search results

Summary of Contents for STUDIOBAY

Reviews:

Related manuals for STUDIOBAY

Brands by name

Popular brands