Allotech HOR 2 Quick Start Manual Download Page 1

I. HS MODE PROGRAMMING

II. BS MODE PROGRAMMING

III. CHANGE MODE (BS TO HS TO BS...)

IV. CHECK THE CURRENT MODE

V. TECHNICAL DETAILS

VI. DECLARATION OF CONFORMITY

VII. WARRANTY

Press the «P» button on your receiver. The receiver’s LED starts to blink. Press and hold the remote control key you 

want to program for 2s.

The receiver’s LED blinks faster and goes off.

Your remote control is correctly programmed.

Press the «P» key on your receiver. The receiver LED flashes.

Press the button on your remote control that you want to program for at least 3s.

The receiver LED flashes faster and goes out.

Your remote control is well programmed.

Each button can be in HS or BS independently of the other buttons of the same remote control.

Keep the button pressed for 35 seconds:

 - The LED will stay fixed (HS mode) or flash red and green after 7 seconds (BS mode) for 25 seconds. The LED 

turns off for 10 seconds and turns solid red.

 - Release the button.

 - Press the same button again: The LED is steady red then flashes green once, then it flashes green twice.

 - Quickly release the button. The LED quickly flashes green and turns off.

 - After 10 seconds, the LED flashes red and green several times and goes out:

You have changed the mode of this key.

If by pressing a key

- the LED flashes 3 times in green, this key is in BS mode

- the LED remains solid green, this key is in HS mode

Power supply: 3V battery - CR2032 || Power consumption: 20 mA || Frequency: 868 MHz

A. Directly on receiver

Only on receiver

B. From another remote control

Press and hold the button you want to program for 35 seconds: 

- The LED is solid green for 25 seconds, goes out for 10 seconds before turning to solid red: Release the button.

Press the same button again:

 - The LED is steady red then flashes green once: Release the button immediately.

 - Press and hold the button on the remote control that you want to clone, positioning it as in the picture (Image 1).

 - The LED of your remote control to be programmed flashes many times in red, then in green and goes out.

 - After 10 seconds, your new remote control will flash red and green several times: Your new remote control is 

programmed.

Allotech hereby declares that this product is in compliance with the essential requirements and other relevant provisions of the

directive 1999/5 / EC. (TR2)

A declaration of conformity is available at www.alloteleccommande.com.

Failure to comply with these instructions renders void Allotech’s responsibility. Allotech may not be held responsible for changes to

norms and standards following the publication of this document.

The warranty covers the remote control purchased in Poland and lasts for 2 years from the date of production. If malfunctions occur (for reasons 

attributable to the manufacturer) and persist within 2 years from the date of manufacture, they will be repaired free of charge or the device will 

be replaced with a new one. If you perform warranty repair or replace the device under warranty, it does not extend the warranty period. The 

manufacturer’s warranty does not cover: Mechanical damage, thermal damage, pilot flooding, damage, battery damage, damage resulting from user 

manipulation, all parts of the remote control that wear out in normal operating conditions, eg. wiping fingerprints, scratches. The manufacturer’s liability 

is limited to the market value of the remote control indicated in the manufacturer’s price list in effect on the date of the filing of the complaint. The 

manufacturer is not responsible for loss, damage or destruction of the system resulting from causes other than inherent defects, and is not responsible 

for damage caused by product defects. In particular, warranty rights do not include the right to recover profits lost due to the failure of the remote 

control. The warranty for the goods sold does not exclude, limit or suspend the rights of the consumer resulting from the mandatory provisions. The 

device must be returned with a warranty card and a completed claim form (available for download from www.proxima.pl in the download tab) to the 

company address. In addition, be aware that an extension of the warranty is possible (see General Terms and Conditions of the Allo Remote Control 

website). It is forbidden to dispose of this device with the collective waste of your house. In accordance with the WEEE directive in force in the EU, this 

device is subject to selective collection.

EN - AlloTech HOR 2 - 4

I. PROGRAMMIERUNG IM HS-MODUS

II. PROGRAMMIERUNG IM BS-MODUS

III. MODUS ÄNDERN (BS ZU HS ZU BS...)

IV. ÜBERPRÜFEN SIE DEN AKTUELLEN MODUS

V. TECHNISCHE DETAILS

VI. KONFORMITÄTSERKLÄRUNG

VII. GARANTIE

Drücken Sie die Taste «P» Ihres Empfängers. Die LED des Empfängers beginnt zu blinken. Halten Sie die 

Fernbedienungstaste, die Sie programmieren möchten, 2 Sekunden lang gedrückt.

Die LED des Empfängers blinkt schneller und erlischt.

Ihre Fernbedienung ist richtig programmiert.

Drücken Sie die Taste «P» Ihres Receivers. Die Empfänger-LED blinkt.

Drücken Sie mindestens 3s lang die Taste auf Ihrer Fernbedienung, die Sie programmieren möchten.

Die Empfänger-LED blinkt schneller und erlischt.

Ihre Fernbedienung ist gut programmiert.

Jede Taste kann unabhängig von den anderen Tasten derselben Fernbedienung in HS oder BS sein.

Halten Sie die Taste 35 Sekunden lang gedrückt:

 - Die LED bleibt dauerhaft (HS-Modus) oder blinkt nach 7 Sekunden (BS-Modus) für 25 Sekunden rot und grün. Die 

LED erlischt für 10 Sekunden und leuchtet durchgehend rot.

 - Lass den Knopf los.

 - Drücken Sie die gleiche Taste erneut: Die LED leuchtet konstant rot, blinkt dann einmal grün und blinkt dann 

zweimal grün.

 - Lassen Sie die Taste schnell los. Die LED blinkt schnell grün und erlischt.

 - Nach 10 Sekunden blinkt die LED mehrmals rot und grün und erlischt:

Sie haben den Modus dieser Taste geändert.

Wenn durch Drücken einer Taste

- die LED blinkt 3 mal grün, diese Taste befindet sich im BS-Modus

- die LED leuchtet durchgehend grün, diese Taste befindet sich im HS-Modus

Stromversorgung: Pile 3V - CR2032 || Energieverbrauch: 20 mA || Frequenz: 868 Mhz

A. Direkt am Empfänger

Nur am Empfänger

B. Von einer anderen Fernbedienung

Halten Sie die Taste, die Sie programmieren möchten, 35 Sekunden lang gedrückt:

- Die LED leuchtet 25 Sekunden lang grün, erlischt 10 Sekunden lang, bevor sie dauerhaft rot leuchtet: Lassen Sie 

die Taste los.

Drücken Sie die gleiche Taste erneut:

 - Die LED leuchtet konstant rot und blinkt dann einmal grün: Lassen Sie die Taste sofort los.

 - Halten Sie die Taste auf der Fernbedienung, die Sie klonen möchten, gedrückt und positionieren Sie sie wie im 

Bild (Image  1).

 - Die LED Ihrer zu programmierenden Fernbedienung blinkt mehrmals rot, dann grün und erlischt.

 - Nach 10 Sekunden blinkt Ihre neue Fernbedienung mehrmals rot und grün: Ihre neue Fernbedienung ist 

programmiert.

Wir, Allotech, erklären, dass dieses Produkt den wesentlichen Anforderungen und weiteren zutreffenden Bestimmungen der Richtlinie

1999/5 / EG entspricht. (TR2)

Eine Konformitätserklärung ist auf der website www.allotelecommande.com.

Die Nichtbeachtung dieser Anweisungen schliebt die Haftung von Allotech und die Garantie aus. Allotech kann nicht für Änderungen

der Normen und Standards nach Veröffentlichung dieser Anleitung haftbar gemacht werden.

Die Garantie gilt für die in Polen gekaufte Fernbedienung und dauert 2 Jahre ab Herstellungsdatum. Treten Funktionsstörungen (vom Hersteller zu 

vertretende Gründe) auf und bestehen innerhalb von 2 Jahren ab Herstelldatum an, werden diese kostenlos repariert oder das Gerät durch ein neues 

ersetzt. Wenn Sie eine Garantiereparatur durchführen oder das Gerät im Rahmen der Garantie austauschen, verlängert sich die Garantiezeit nicht. 

Die Herstellergarantie erstreckt sich nicht auf: Mechanische Schäden, thermische Schäden, Überflutung des Piloten, Schäden, Batterieschäden, 

Schäden durch Manipulationen durch den Benutzer, alle Teile der Fernbedienung, die unter normalen Betriebsbedingungen verschleißen, z. 

Abwischen von Fingerabdrücken, Kratzern. Die Haftung des Herstellers ist auf den Marktwert der Fernbedienung beschränkt, der in der am Tag der 

Reklamation gültigen Preisliste des Herstellers angegeben ist. Der Hersteller haftet nicht für Verlust, Beschädigung oder Zerstörung des Systems, 

die auf andere Ursachen als inhärente Fehler zurückzuführen sind, und haftet nicht für Schäden, die durch Produktfehler verursacht werden. Die 

Gewährleistungsrechte umfassen insbesondere nicht den Anspruch auf Rückforderung des durch den Ausfall der Fernbedienung entgangenen 

Gewinns. Die Gewährleistung für die verkauften Waren schließt die Rechte des Verbrauchers, die sich aus den zwingenden Bestimmungen 

ergeben, nicht aus, beschränkt oder setzt diese aus. Das Gerät muss mit einer Garantiekarte und einem ausgefüllten Reklamationsformular (zum 

Download unter www.proxima.pl im Download-Tab verfügbar) an die Firmenadresse zurückgesendet werden. Beachten Sie außerdem, dass eine 

Garantieverlängerung möglich ist (siehe Allgemeine Geschäftsbedingungen der Allo Remote Control Website). Es ist verboten, dieses Gerät über den 

Hausmüll zu entsorgen. Gemäß der in der EU geltenden WEEE-Richtlinie unterliegt dieses Gerät der selektiven Sammlung.

DE - AlloTech HOR 2 - 4

Reviews: