manualshive.com logo in svg

Allied Stingray, Technical Manual, Page: 163 / 357

Share
Download
Allied Stingray Technical Manual Download Page 163

Description of the data path

STINGRAY Technical Manual

 

V4.4.2

163

Binning and sub-sampling access

The binning and sub-sampling modes described in the last two chapters are 
only available as pure binning or pure sub-sampling modes. A combination 
of both is not possible.

As you can see there is a vast amount of possible combinations. But the num-
ber of available Format_7 modes is limited and lower than the possible com-
binations.

Thus access to the binning and sub-sampling modes is implemented in the 
following way:

•

Format_7 Mode_0

 is fixed and cannot be changed

•

A maximum of 7 individual AVT modes can be mapped to 

Format_7 

Mode_1

 to 

Mode_7

(see 

Figure 90: Mapping of possible Format_7 modes to F7M1...F7M7

 on 

page 164)

•

Mappings can be stored via register (see Chapter 

Format_7 mode map-

ping

 on page 332) and are uploaded automatically into the camera on 

camera reset.

•

The 

default settings

 (per factory) in the Format_7 modes are listed in 

the following table

Format_7

Stingray monochrome cameras 
Format_7

Stingray color cameras Format_7

Mode_0

full resolution, no binning,

no sub-sampling

full resolution, no sub-sampling

Mode_1

2 x 

horizontal

 binning

Only F-201C/F-504C:

 2 x 

horizontal

 binning

Mode_2

2 x 

vertical

 binning

Only F-201C/F-504C:

 2 x 

vertical

 binning

Mode_3

2 x 

full

 binning

Only F-201C/F-504C:

 2 x 

full

 binning

Mode_4

2 out of 4 

horizontal

 sub-sampling

2 out of 4 

horizontal

 sub-sampling

Mode_5

2 out of 4 

vertical

 sub-sampling

2 out of 4 

vertical

 sub-sampling

Mode_6

2 out of 4 

full

 sub-sampling

2 out of 4 

full

 sub-sampling

 Table 47: Default Format_7 binning and sub-sampling modes (per factory)

Note

•

A 

combination

 of binning and sub-sampling modes is 

not possible

.

Use either pure binning or pure sub-sampling modes.

•

The Format_ID numbers 0...27 in the binning / 

sub-sampling list on page 164 do 

not

 correspond to any 

of the Format_7 modes.

Summary of Contents for Stingray






































































































































































































































































































































































Reviews:

No comments