manualshive.com logo in svg

Allied Telesis IE340 Series, Installation Manual, Page: 130 / 136

Share
Download
Allied Telesis IE340 Series Installation Manual Download Page 130

IE340 Series Installation Guide

130

Power Specifications

Note

For power supply specifications, see “Power Supplies” on page 49.

Note

The cooling requirements of the switch are smaller than the power 
draw because most of the load is dissipated at the PoE powered 
device and along the cabling. Use these BTU ratings for facility 
capacity planning.

Table 19. Input Voltage Specifications

Switch

PoE

PoE+

Non-PoE

IE340-12GP

46-57VDC

52.5-57VDC

18-57VDC 

IE340-20GP

18-57VDC 

IE340L-18GP

46-57VDC

IE340-12GT

N/A

N/A

18-57VDC 

Table 20. Maximum Power Consumptions

IE340-12GP

271 watts (including PDs’ consumption
31 watts (excluding PDs’ consumption)
24 watts (without PoE load)

IE340-20GP

IE340L-18GP

IE340-12GT

24 watts

Table 21. Heat Dissipation

PoE

PoE+

Non-PoE

IE340-12GP

105.8 BTU/hr

105.8 BTU/hr

81.9 BTU/hr

IE340-20GP

IE340L-18GP

IE340-12GT

N/A

N/A

Summary of Contents for IE340 Series









































































































































Reviews:

No comments