manualshive.com logo in svg

Allied Telesis AT-S79, User Manual, Page: 81 / 210

Share
Download
Allied Telesis AT-S79 User Manual Download Page 81

AT-S79 Management Software User’s Guide

Section I: Using the Menus Interface

81

Note

For explanations of VLAN name and VLAN identifier, refer back to 
“VLAN Name” on page 74 and “VLAN Identifier” on page 74.

Tagged and

Untagged Ports

You need to specify which ports will be members of the VLAN. In the case 
of a tagged VLAN, the ports usually consist of both untagged and tagged 
ports. You specify which ports are tagged and which untagged when you 
create the VLAN.

An untagged port, whether a member of a port-based VLAN or a tagged 
VLAN, can be in only one VLAN at a time. However, a tagged port can be 
a member of more than one VLAN. A port can also be an untagged 
member of one VLAN and a tagged member of different VLANs 
simultaneously.

Port VLAN

Identifier

As explained earlier in the discussion on port-based VLANs, the PVID of a 
port determines the VLAN where the port is an untagged member.

Because a tagged port determines VLAN membership by examining the 
tagged header within the frames that it receives, you could conclude that 
there is no need for a PVID. However, the PVID is used if a tagged port 
receives an untagged frame — a frame without any tagged information. 
The port forwards the frame based on the port’s PVID. This is only in 
cases where an untagged frame arrives on a tagged port. Otherwise, the 
PVID of a tagged port is ignored.

Guidelines to

Creating a

Tagged VLAN

Below are the guidelines to creating a tagged VLAN.

ˆ

Each tagged VLAN must be assigned a unique VID. If a particular 
VLAN spans multiple switches, each part of the VLAN on the different 
switches must be assigned the same VID.

ˆ

A tagged port can be a member of multiple VLANs.

ˆ

An untagged port can be an untagged member of only one VLAN at a 
time.

ˆ

The switch can support up to a total of 256 port-based and tagged 
VLANs.

Summary of Contents for AT-S79



















































































































































































































Reviews:

No comments