Allied Telesis 86241-06 Release Note Download Page 16

16

Patch Release Note

Patch 86241-05 for Software Release 2.4.1

C613-10340-00 REV E

The SHOW IPV6 INTERFACE command now shows the address lifetime 
aging status that is determined by the DECREMENT parameter in the ADD 
IPV6 INTERFACE command. The default valid and preferred address 
lifetimes have been changed to 30 days and 7 days respectively.

The interface address preferred lifetime was not operating correctly. This 
issue has been resolved.

A fatal error occurred when the command SET FR=0 LMI= was executed if 
the LMI was already set to ANNEXA, ANNEXB or ANNEXD. This issue 
has been resolved.

A fatal error occurred when a PING was executed over an IPV6 tunnel that 
had previously been deleted. Also, packet forwarding with link-local 
addresses was not working correctly. These issues have been resolved.

In some situations, multihomed interfaces caused the Firewall to apply 
NAT and rules incorrectly when packets were received from a subnet that 
was not attached to the receiving interface. This issue has been resolved.

BGP was not sending a withdraw message to a peer for a withdrawn or 
replaced route when the new best route came from that peer. This issue has 
been resolved.

A buffer leak was occurring in IPv6 fragmentation. This issue has been 
resolved.

IP is now informed when an Ethernet interface goes up or down, after a 2.5 
second delay. 

The sequence number extracted from the AH and ESP header was in the 
wrong endian mode, which caused an FTP error with IPSEC anti-replay. 
This issue has been resolved.

It is now possible to set the domain name of the SMTP server to none 
(0.0.0.0) with the SET FIREWALL POLICY SMTPDOMAIN command, even 
if a server name has not previously been specified.

PCR: 02313

Module: IPV6

Network affecting: No

PCR: 02320

Module: IPV6

Network affecting: No

PCR: 02321

Module: FR

Network affecting: No

PCR: 02326

Module: IPv6

Network affecting: No

PCR: 02327

Module: IPG/FIREWALL

Network affecting: No

PCR: 02328

Module: BGP

Network affecting: No

PCR: 02330

Module: IPv6

Network affecting: No

PCR: 02331

Module: IPG, ETH

Network affecting: No

PCR: 02332

Module: IPSEC

Network affecting: No

PCR: 02334

Module: FIREWALL

Network affecting: No

Summary of Contents for 86241-06































Reviews: